13
PIN Lock Menu Supplement
These supplemental instructions apply to
all vehicles equipped with:
Firmware
Firmware
Firmware
The Tazer PIN Lock
allows you to set a steering
wheel button sequence (PIN) that must be entered before
the vehicle can be driven and provides for the vehicle to
become immobilized in the event of an attempted theft
through triggering the PIN Lock, key pairing or triggering
the factory alarm.
This is the most complex feature of the
Tazer and provides a high level of security against vehicle
theft.
This PIN will need to be entered when the vehicle is
started or after you exit the running vehicle with your key.
List of Menu Options (in order):
“
Set PIN
” set the desired button sequence (PIN). Changes to
“Clear PIN” once set
“
Clear PIN
” erase the PIN. Changes to “Set PIN” once selected
“
Enable/Disable PIN
” quickly disable or enable the PIN Lock
feature without erasing the PIN. This enabled by default
“
KillPedalNow
” a “high-security parking mode” which will disable
the gas pedal until the next time the PIN is entered
“
PIN Brakes
” toggle whether triggering the PIN Lock will lock all
four brakes when the vehicle is stopped.
“
PIN Horn
” toggle whether triggering the PIN Lock will cause the
horn to honk in a randomized pattern.
“
PIN Lights
” toggle whether triggering the PIN Lock will start a
Light Show.
“
PIN Pedal
” toggle whether triggering the PIN Lock or vehicle
alarm, or an attempt to pair a key, will disable the gas pedal. This
will function regardless of PIN enable/disable.
“
KillByFob
” toggle whether locking the vehicle from the fob will
disable the gas pedal.
“
Carjack
” toggle Carjack Mode, which triggers when the key exits a
running vehicle. This requires that a PIN is set and that PIN is enabled.
“
PIN Clear Time
” set whether it should take 10 or 60 minutes to
clear a forgotten PIN using the process described below. This is set
to 10 minutes by default.
Setting your PIN:
1. Select the “Set PIN?
” option in the
PIN Lock
menu with
◁
/BACK(HOLD) + CRUISE On/Off
to begin the process.
2. Enter a
one to six button sequence
that will allow the
operator to drive the vehicle. The symbols in parentheses
will appear on the screen to indicate the respective buttons.
Your button choices are:
• (+)
• Cruise - (-)
• Cruise Cancel (<)
• Cruise RES (>)
and if you have Adaptive Cruise Control
• Near ACC (N)
• Far ACC (F)
• ACC Enable (A)
Hitting a seventh button will abort the process
and
allow you to start over.
3. Save your PIN with
CRUISE On/Off
. “Pin Saved” will display.
After turning the vehicle off, this PIN will now be required to drive
the vehicle
and
“Set PIN?
”
will change to
“Clear PIN.”
Removing the PIN:
1.
Start yourt vehicle and enter your PIN.
2. Navigate to the PIN Lock menu and select
“Clear PIN.”
After turning the vehicle off, the PIN will no longer be required to
drive the vehicle
and
“Clear PIN?
”
will change to
“Set PIN.”
If you forget your PIN:
To remove the PIN Lock after the PIN Lock is triggered:
1. Select
“Clear PIN”
from the PIN Lock menu. The dash screen
will read
“Brake+Hazard.”
2.
Turn on your hazard lights and apply the foot brake. By default,
this will trigger a 10-minute countdown.
3. Keep the vehicle running and your foot on the brake until this
countdown is finished and the PIN Lock will be removed.
NOTE:
In any instance that the vehicle is immobilized by the Pin Lock
feature, in the Wrangler 4XE, the motor will shut off and the vehicle will
become stuck in Park instead of locking all four brakes.
NOTE:
See the “Customizing PIN Lock” section below for more details
about the toggleable measures.
NOTE:
The EVIC screen must be set to Audio for text related to the PIN
Lock feature to display on the screen. PIN Lock will still operate as
descrubed otherwise.
NOTE:
2011 vehicles will see “Keyfob Battery Low” instead of “Keyfob Not
Detected” during dashboard reminders.
NOTE:
If utilizing PIN Pedal, the vehicle may stumble or stall after entering
your pin while the pedal is reenabled.
