manualshive.com logo in svg

Yunca Gas EROS, Руководство пользователя

Поделиться
Скачать
Yunca Gas EROS Скачать руководство пользователя страница 9

25-07-01 

Page 9 of 23                      Operation Instructions for Eros Free Standing Gas Fire July 2001.doc

 

 

PRESSURE TESTING:

                                                                                                       

 
The pressures listed on the previous page can be tested using a manometer. 
 
To attach manometer, first remove the inspection cover from back panel. The cover is located 
directly behind the control and is removed by unscrewing the two top screws. 
 
This will expose the back of the control so manometer tubes can be attached to the 

pressure taps

 

as shown below.   
 
The inlet pressure can be adjusted via in line regulators in the supply to the heater, and the outlet 
(operating) pressure by adjusting the valves internal regulator. To locate the valves 

regulator 

adjustment screw

 the plastic control cover must be removed from the front of the valve. This is 

done by removing the bottom screw and inserting a small flat head screwdriver into the slot at 
the top on the front of this cover and pulling the cover off.  Refer to fig. 4 below 

 

THERMOSTAT 

 
The thermostat sensing bulb is found on the fan back panel held in a saddle. 
 
In some installations the thermostat sensing bulb may need to be repositioned to accurately sense 
the room temperature.   Reposition in an unobtrusive place. 

 
 
CONNECTING THE FAN

 

 
The fan should be connected to the mains supply (240V 50Hz) via the 3m flex and 3pin plug  
 

Содержание EROS
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды