YSI 5200A Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 139

background image

YSI 5200A
203

YSI 5200A
202

AquaManager

-

print graph and printer setup

-

close node window

-

copy graph to clipboard

-

insert manual event

-

graph management

-

customize graph settings

-

clear graph overlays

-

view data, calibration, event, & configuration event logs

-

restore Node Window size to include access to systems management and poll
node buttons

-

Systems Management access - viewing and uploading a configuration to a
5200A

-

Graph Display options

-

Manually poll node button

-

Current data is displayed at the top of the graph during a manual poll

Systems Management

To open Systems Management, click on the Systems Management button located
to the right of the graph in the Node Window. Use the tabs to view and upload a
configuration to the node. The node configuration displayed is based on last poll.

07/30/2008

The following configuration and tasks are performed from Systems Management
forms:

-

view and configure node sensor and aux systems

-

view and configure node timer and feed timer systems

-

view and configure most node systems (5200A system menu)

-

configure node mapping icons

Notes:

-

Always manually poll the 5200A after uploading configuration changes and
verify that the uploaded information is retained. When configuration changes
are uploaded using AquaManager at the same time configuration changes are
being made by a user in the menus at the 5200A, AquaManager uploads may
not be saved depending on the timing of keystrokes at the 5200A.

-

The Run Screen must be displayed during normal operation.

If the 5200A

is not at the run screen during AquaManager uploading, pressing

at

the 5200A will only save certain configuration changes.

Database Management

For optimal operation and safeguarding, compact and back up the AquaManager
database. Uncompacted Access database(s) may become > 1GB when polling large
networks and/or large data logs. Compact the database from the Explorer Win-
dow Tools>Database Maintenance>Compact Database or from the System Wide
Properties>Gen. settings tab.

Configure an automatic weekly backup from the System Wide Properties>Database
Backup tab.

Note:

AquaManager

«
...
100
101
102
103
104
...
»

Содержание 5200A












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5200A

Бренд: TAC Страницы: 4

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 20

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: HandyTrac Страницы: 14

Бренд: TA Страницы: 6

Бренд: Mackie Страницы: 16

Бренд: TANDBERG Страницы: 47

Бренд: Voltech Страницы: 8

Ambience Control 1

Бренд: EuroLite Страницы: 20

Бренд: SKF Страницы: 88

Saxun Mosquito Screen Lateral Door 2020

Бренд: Gimenez Ganga Страницы: 2

Бренд: Keysight Technologies Страницы: 78

Бренд: bluelab Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды