LED indicator
Step 1:Remove the remote from
previous zigbee network if it has already
been added to it, otherwise pairing will
fail. Please refer to the part "Factory
Reset Manually".
Step 2:From your zigbee controller or
hub interface, choose to add device or
accessory and enter Pairing mode as
instructed by the controller.
Press and hold down until LED
indicator turns on.
Step 3:Immediately short press to
search nearby network, indicator
flashes every 1 second, 20 seconds
timeout if there is no network. Indicator
will then blink 5 times quickly for
successful pairing.
From your ZigBee controller or hub
interface, choose to delete or reset
the remote as instructed, indicator
flashes 3 times quickly to indicate
successful removing.
LED indicator
S tep 2 :
Immediately short press 5 times
continuously, indicator flashes 3 times
quickly to indicate successful reset.
S tep 1 :
Press and hold down until LED
indicator turns on.
Note: all configuration parameters will be
reset after the remote is reset or removed
from the network
3. Zigbee network pairing through coordinator or Hub (Added to a Zigbee Network)
Step 4:
5. Removed from a Zigbee Network through Coordinator or Hub interface
Note: 1 After pairings succesfully the remote information will appear on the controller or hub interface.
2: No remote information will appear on the hub interface if pairing to Philips Hue Bridge.
6. Factory Reset Manually
Note
: the device shall be added to a network, the remote added to the same one or not added to any network
.
ZigB ee L ighting D ev ic e
< 10cm
S tep 1
: Set the Touchlink paired zigbee
device to start TouchLink
commissioning, please refer to its
manual to learn how
.
LED indicator
S tep 2
: Bring the remote within 10cm of
the lighting device
.
S tep 3
: Short
press
the group button
that the device was linked to
.
S tep 5
: Immediately short press twice to
start TouchLink removing of the remote
.
LED indicator flashes fast for 3S, then
flash 6 times slowly to indicate
successful removing.
ZigB ee L ighting D ev ic e
< 10cm
S tep 1
: Set the zigbee lighting device to
start TouchLink commissioning, please
refer to its manual to learn how
.
LED indicator
S tep 2
: Bring the remote within 10cm of
the lighting device
.
S tep 3
: Press and hold down any group
button to start Touch
L
ink
c
ommissioning
of the remote
.
LED indicator flashes fast
for 3S, then flash 6 times slowly to
indicate successful pairing to the device
and the light connected to the device
will blink twice.
ZigB ee L ighting D ev ic e
< 10cm
S tep 1
: Set the zigbee device to start
TouchLink commissioning, refer to its
manual
.
LED indicator
S tep 2
: Bring the remote within 10cm of
the lighting device
.
S tep 3
: Press and hold down until LED
indicator turns on
.
S tep 4
:Immediately short press 5 times to
start Touch Reset of the remote
.
LED
indicator flashes fast for 3S, then flash 3
times slowly to indicate successful reset.
S tep 4
: Press and hold down until LED
indicator turns on
.
Note: 1 Directly Touchlink) both not added to a Zigbee network) each remote can link with 30 devices.
2 Touch link after both added to a Zigbee network, each remote can link with max 30. devices.
3 For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4 After TouchLink, the remote can control the linked lighting devices
4. Touch Link to a Zigbee Lighting Device
7. Remove Touchlink Paired Zigbee Lighting Device
8 Factory Reset a Lighting Device (Touch Reset)
