YORKVILLE LP-LED 2X, Руководство пользователя

Страница: 5 / 22

S t a g e L i g h t i n g
LP-LED/X
3
LP-LED2X 1,2/3,4 Switch
The LP-LED2X has 2 light pods but the Yorkville lighting controllers such as the LP-C4 or LP-C12
use a 4 channel signal. The 1,2/3,4 switch selects which 2 of the 4 channels the bar responds to.
Power Consumption
The advantage for using LED versus conventional incandescent lighting is two-fold, not only does
the unit give off less heat but also consumes less than 5-20% of the energy. This eliminates the
need for separate AC power circuits just to run the lights!
Power consumption is rated under 200 watts which depends on the color choice and intensity.
The light pods and the base are fan cooled. The AC connector will mate with a standard IEC cable
or with a special locking cable (sold seperately). Line voltage can be anywhere from 100 to 240
volts AC enabling you to use the LP-LED/X Bars practically anywhere!
Yorkville sound LP-C12 and LP-C4 Controllers
The LP series controllers provide an easy way to control LP-series lights. The LP-C4 is a simple
controller intended for foot controlled applications and small applications. The LP-C12 provides
extensive effects, effects patch and scene controls in an especially easy to use format. The use
of LP-series controllers also are the easiest way to synchronize effects between bars. The LP-C12
patch allows some pods to be under scene control while other pods are running effects.
Yorkville Sound LP-608 Lighting Controller
When operating with the Yorkville Sound LP-608 lighting controllers the color controls on the LP-
LED/X Bars remain active. The Color control can be used to select the color of each pod or if
the Color control is set to off then the LP-Controller's intensity control becomes the color control
(including off) but the intensity is not controllable.
Note: Operation with the legacy LP-608 controller will require a ‘gender reversing’ adapter in line with the
XLR cable. This was done to prevent accidental connection to a DMX™ controller possibly causing damage.
Max AC Input Voltage
100-240VAC 50/60 Hz
Power Consumption LEDs
14 watts per LED (4 LEDs, 56 watts per pod)
Power Consumption LP-LED2X: 120VA, 1.0A @ 120VAC Nominal
LP-LED4X: 240VA, 2.0A @ 120VAC Nominal
Stand Mount Size
1 3/8 inch Round
Controller Cable Yorkville: Standard Shielded 3-pin XLR Cable
Other
DMX: Standard Shielded 3-pin XLR Cable
Dimensions (LWH) LP-LED2X: 24 x 4.8 x 8 inches (61 x 12.25 x 20.4 cm)
LP-LED4X: 31 x 4.8 x 8 inches (78.8 x 12.25 x 20.4 cm)
Weight LP-LED2X: 9.5 lbs (4.3 kg)
LP-LED4X :14.6 lbs (6.6 kg)
Specifications
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.