background image

5326602-XIM-B-1019

Johnson Controls Ducted Systems

5

Installation

Installation Safety Information

Read these instructions before continuing this appliance 
installation. This is an outdoor combination heating and cooling 
unit. The installer must assure that these instructions are made 
available to the consumer and with instructions to retain them 
for future reference.
1.

Refer to the unit rating plate for the approved type of gas 
for this product.

2.

Install this unit only in a location and position as specified 
on Page 7 of these instructions.

3.

Never test for gas leaks with an open flame. Use 
commercially available soap solution made specifically for 
the detection of leaks when checking all connections, as 
specified on Pages 5, 26, 27 and 51 of these instructions.

4.

Always install furnace to operate within the furnace's 
intended temperature-rise range with the duct system and 
within the allowable external static pressure range, as 
specified on the unit name/rating plate, specified on 
Page 53 of these instructions.

5.

This equipment is not to be used for temporary heating of 
buildings or structures under construction.

Preceding Installation

1.

Remove the two screws holding the brackets in the front, 
rear and compressor side fork-lift slots.

Figure 1: Unit Shipping Bracket

2.

Turn each bracket toward the ground and the protective 
plywood covering will drop to the ground.

3.

Remove the condenser coil external protective covering 
prior to operation.

4.

Remove the toolless doorknobs and instruction packet 
prior to installation.

Figure 2: Condenser Covering

Figure 3: Compressor Section

5.

If a factory option convenience outlet is installed, the 
weatherproof outlet cover must be field installed. The cover 
shall be located behind the filter access panel. To install 
the cover, remove the shipping label covering the 
convenience outlet, follow the instructions on the back of 
the weatherproof cover box, and attach the cover to the 
unit using the (4) screws provided.

FIRE OR EXPLOSION HAZARD
Failure to follow the safety warning exactly could result 
in serious injury, death or property damage.
Never test for gas leaks with an open flame. use a 
commercially available soap solution made specifically 
for the detection of leaks to check all connections. A fire 
or explosion may result causing property damage, 
personal injury or loss of life.

Bracket
Screws

Turn down

380/415-3-50 units with factory installed Powered 
Convenience Outlet Option are wired for 415v power 
supply. Change Tap on transformer for 380-3-50 
operation. See unit wiring diagram.

Condenser 
Coil External 
Protective 
Covering

Barometric 
Relief Hood 
in Shipping 
Location
(if Included)

Toolless 
Doorknobs

Installation 
Instruction 
Packet

Содержание ZF SERIES


































































Отзывы: