York YCAL Series Скачать руководство пользователя страница 138

Страница: 138 / 174

JOHNSON CONTROLS

138

FORM 150.66-NM3

ISSUE DATE: 09/25/2020

SECTION 8 - UNIT OPERATION

The VFD will ramp up the speed of the fan as pres-

sure rises above the low end of the speed control range.

Throughout the pressure control range, the VFD con-

trols the speed of the fan based on discharge pressure in

the range of approx 160-180 psig. At pressures above

180 psig, the VFD will run the system fan at full speed.

As pressure drops below 180 psig, the VFD will slow

the speed of the fan to try to maintain discharge pres-

sure within the control range. The VFD will try to

maintain pressure in the range of 160-180 psig by rais-

ing and lowering the speed of the fan. If pressure drops

below 160 psig, the VFD will virtually turn the system

fan completely off. Some slight fan movement or very

slow rotation may be noted, although the fan may ap-

pear to stop completely.

Configuration (Jumpers and Potentiometers)

Each VFD is pre-configured at the factory prior to ship

ping and should be ready for operation when it arrives

onsite. A quick check of the settings is recommended.

The jumpers must be in the positions shown in the fol-

lowing Table.

Chillers built in 2005 and early 2006

were configured with J4 IN. This

jumper must be removed. Also be sure

to check J2 and remove if necessary.

FIG. 15 – POTENTIOMETER SETTINGS

POTENTIOMETER SETTINGS

180 PSI

20 PSI

LD11300A

Potentiometer settings are also preset at the factory.

The potentiometers should be in the positions shown

in Fig.15. The pots do not have numerical settings and

are set according to the arrow positions indicated. DO

NOT change the potentiometer settings unless they do

not match the positioning of the potentiometers shown

in Fig. 15. P1 should be full CW (180 psig) and P2

should be full CCW (20 psig). Modifying these settings

may cause damage to the chiller or control problems.

The P1 pot sets the setpoint which is the top end of the

control range. This setting is the discharge pressure at

which the fan will be operating at full speed. The P2

pot sets the range. This is the range of pressure where

the VSD modulates the fan speed from 0 RPM to full

speed. The range is subtracted from the setpoint to cal-

culate the 0 RPM pressure.

VFD JUMPERS

Remove

IN for 60Hz

Remove for 50Hz

Содержание YCAL Series















































































































































































Результаты поиска

Содержание YCAL Series

Отзывы:

Похожие инструкции для YCAL Series

Бренды по названию

Популярные бренды

York YCAL Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание YCAL Series

Отзывы:

Похожие инструкции для YCAL Series

Бренды по названию

Популярные бренды