background image

8

Installation and Maintenance

3.2.3 Install the indoor unit.

The installation of the indoor unit is shown in Fig. 3.4.

(1) How to fix the suspension bolts and the nuts
As shown in Fig. 3.5, the nuts are fixed by
four bolts.

Nut

Indoor unit

Washer

Double nut

Fig. 3.5 Suspension bolts and nuts

Approx 50mm

Suspension bolts

( Field supplied )

 (4-M10 or W3/8)

Nuts and 
washers (4-
M1 0 or W3/ 8)  
( Field supplied )

Fig. 3.4 The installation of the indoor unit

Fig. 3.3 Suspension bolts

(2) Install the indoor unit

As shown in the following figure, place the left 

hanger bracket on the nuts and washers of the 
suspension bolts.

Make sure that the left hanger bracket has been 

fixed on the nuts and washers securely, install the right 
hanger bracket suspension hook on the nuts and 
washers.
(When installing the indoor unit, you can slightly 
remove the suspension bolts.)

·

·

Fig. 3.6

3.2.4 The horizontal adjustment of the indoor unit 
(1) Make sure that the hanger bracket is fixed by the nuts 
and the washers.
(2) Adjust the height of the unit.
(3) Check if the unit is positioned horizontally.

Fig. 3.7

(4) After the adjustment, tighten the nuts and swear  
the thread locker on the suspension to prevent the 
nuts from loosening.

(1) During the installation, please cover the unit with the 
plastic cloth to keep it clean.
(2) Make sure that the unit is installed level by using a level or 
a plastic tube filled with water in instead of a level, adjust the 
top surface of the unit to the surface of the water at both ends 
of the plastic tube and adjust the unit horizontally.(one thing to 
watch out for in particular is if it is installed so that the slope is 
not in the direction of the drain piping, as this might cause 
leaking.)

CAUTION

Rack 

Double nuts 
and washers 

Hanger bracket 

Suspension bolt 

Indoor unit

3.2.5 Installing the duct 

·

Make sure the external static pressure of the unit is within
the range.

·

Connect the duct and intake-side flange.

·

Connect the duct and outlet-side flange.

·

The connection of indoor unit and air duct must be well

sealed and kept warm with insulation material. 
<Example>

(Unit:mm)

CAUTION

Canvas duct

Horizon

Service mouth

Air inlet
(with filter)

600mm-600mm

Air-outlet

The valve for the amount of air

Insulation material

Outside air
(through
 the filter)

Static pressure
box

Canvas duct

Static pressure
box

The valve for 
the amount of air

a

b

c

d

Air outlet

Air inlet

Model

Capacity (Btu/h)

a

b

c

d

24K

934

900

669

720

36K/42K/48K/55K

1334

1300

756

800

Содержание YAKN09BZNWEUH1




















Отзывы: