York Pyrenees Series Скачать руководство пользователя страница 24

Страница: 24 / 53

7. Electronic function

7.1 Abbreviation

T1: Indoor room temperature

T2: Coil temperature of evaporator

T3: Coil temperature of condenser

T4: Outdoor ambient temperature

T5: Compressor discharge temperature

7.2 Display function

7.2.1 Icon explanation on indoor display board.

Digital display:

Displays the temperature settings when the air

conditioner is operational.

Displays the room temperature in FAN mode.

Displays the self-diagnostic codes.

Dispalys

‘

’ for three seconds when Timer

ON, Fresh, Swing, Turbo or Silence feature is

activated.

Dispalys

‘

’ for three seconds when Fresh,

Swing, Turbo or Silence feature is cancelled.

Dispalys

‘

’ under deforsting operation.

Dispalys

‘

’ when anti-cold air feature is

activated under heating mode.

Dispalys

‘

’ during self clean operation (if

aplicable).

Dispalys

‘

’ under 8 heating operation (if

aplicable).

When ECO function(optional) is actived,the

“

” illuminates gradually one by one as

In one second interval.

NOTE:

A guide on using the infrared remote is not

included in this literature package.

Содержание Pyrenees Series






















































Результаты поиска

Содержание Pyrenees Series

Отзывы:

Похожие инструкции для Pyrenees Series

Бренды по названию

Популярные бренды

York Pyrenees Series, Руководство по обслуживанию

Результаты поиска

Содержание Pyrenees Series

Отзывы:

Похожие инструкции для Pyrenees Series

Бренды по названию

Популярные бренды