York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 76 / 160

JOHNSON CONTROLS

FORM 160.79-O3

ISSUE DATE: 11/09/2018

SECTION 2 – OPTIVIEW CONTROL CENTER

This screen displays the chiller oil sump along with

the compressor oil cooler. All of the setpoints for com-

pressor Variable Speed Drive Oil Pump are maintained

here. The oil pump can be manually controlled from

here. The screen is identical for oils pumps 1 and 2.

DISPLAY ONLY
Oil Pump Run Output (LED)

Illuminated when the associated compressor Variable

Speed Oil Pump Drive is being commanded to run.

Otherwise, it is extinguished.

Oil Pressure

Displays the pressure differential between the associ-

ated Pump oil pressure (HOP) transducer and the com-

mon Sump oil pressure (LOP) transducer. If this com-

pressor is the lead compressor, includes offset pressure

derived from auto-zeroing during the compressor pre-

lube of the lead compressor. However, if compressor

#2 is the lead compressor, this value includes offset

pressure derived from auto-zeroing during compressor

#2 Pre-lube (refer to auto-zeroing explanation under

the Compressor Screen). If either transducer used to

calculate this differential is out of range, the display

field will show XX.X.

Pump Oil Pressure (HOP)

Displays the high side oil pressure measured at the

compressor bearing input.

Oil Pump Drive Command Frequency

Displays the speed command that is being applied to

the compressor Oil Pump Variable Speed Drive.

Setpoint or Target Oil Pressure

Displays the oil pressure setpoint that Variable Speed

Oil Pump is controlling to. During the pre-lube and for

the first 15 seconds of System Run, this is the target

Setpoint, and is fixed at 45.0 PSID. For the remainder

of compressor run, it is the programmed Setpoint Oil

Pressure.

Oil Seal Lubrication Time Remaining

If a Standby Lubrication is in progress on compressor

#1, displays the time remaining in the 2-minute opera-

tion.

Next Oil Seal Lubrication

If compressor #1 is not running, displays the time re-

maining until the next Standby Lubrication.

OIL PUMP 1 AND 2 SCREEN

FIGURE 25 -

OIL PUMP 1 SCREEN

LD27864

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды