York OPTIVIEW YD Series Скачать руководство пользователя

Страница: 103 / 160

JOHNSON CONTROLS

103

SECTION 2 – OPTIVIEW CONTROL CENTER

FORM 160.79-O3

ISSUE DATE: 11/09/2018

This screen allows the Operator to choose what units

of measurement to display parameters in, the screen

languages, and the date format.
Each Custom User value is not linked to a specific but-

ton. Instead, the Change button is pressed which en-

ables the cursor arrows which are used to highlight the

Custom User parameter the user wishes to modify. At

this point the ‘

’ (Check) button is pressed and the

value may be entered.

DISPLAY ONLY

None

PROGRAMMABLE
System Language

Access Level Required: OPERATOR

Allows the user to define the language for all Screens.

The desired language is selected by scrolling through

the list of those available. English is the Default lan-

guage and is selected by pressing the Up Arrow key

when the dialog box appears during the selection pro-

cess. The selected language will not be displayed un-

til after the user navigates from the USER Screen to

another Screen. Available languages are English, Tra-

ditional Chinese, Simplified Chinese, French, Portu-

guese, Spanish, Italian, German, Hungarian, and Turk-

ish.

English / Metric Units

Access Level Required: OPERATOR

Define the unit system (English or Metric) used by the

chiller display.

Custom User ID (4)

Access Level Required: SERVICE

This allows the user to specify up to four (4) Custom

User ID values. Each user ID will then require a cor-

responding Password and User Level. A User ID can

be defined for various maintenance personnel. Service

Technicians refer to

Service Manual (Form 160.79-

M1)

Custom User Password (4)

Access Level Required: SERVICE

This allows the user to specify up to four (4) Custom

Password values. Each Password will then require a

corresponding User ID and User Level. Service Tech-

nicians refer to

Service Manual (Form 160.79-M1)

USER SCREEN

LD27876

FIGURE 37 -

USER SCREEN

Содержание OPTIVIEW YD Series

































































































































































Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды

York OPTIVIEW YD Series, Руководство пользователя

Результаты поиска

Содержание OPTIVIEW YD Series

Отзывы:

Похожие инструкции для OPTIVIEW YD Series

Бренды по названию

Популярные бренды