SECTION 2
Now open Box 3 which contains the following parts:
Part No.
Qty.
Description
BOX 3
Assemble Pt.2223 (tear drop piece) to Pt.2250 using the
parts listed above and following diagram D.
(A)
Install two long bolts and four rollers in the
back of the glide channel and tighten.
(B)
Attach Pt.2223 (flat side to the back) using one
x quick change bolt, one x 3/8" nyloc nut and one
Pt.1242 glide stamping.
Before tightening align and centre Pt.2223.
(C)
Install bolts and rollers into the front of Pt.2223
and tighten, then put this part to one side.
quick change
bolt
Part No.
Qty.
Description
BAG 77
33A33
5/16" Nyloc Nut
3
33A382
5/16" x 1 1/2" HH Bolt
3
33A53
3/8" Nyloc Nut
9
41D151
3/8" x 5 3/4" HH Bolt
4
with 3/8" thread lenght
41B08
Pt.1235 Roller Glide
8
33A436
Glide Quick Change Bolt
1
33B38
Pt.1242 Glide Stampings
2
Locate Bag 77 and check contents as listed:
32B39
Bag 29 Cables
1
32B89
Bag 79
1
32B90
Bag 80
1
32B91
Bag 81
1
21E2220
1
21E2221
1
21E2223
1
21E22241
2
33B021
Pin 159
2
33B022
Pin 160
1
21E2228
2
21E2240
1
21E1224
1
32E68
Bag 9432
(This bag contains
1
collars & allen key for locking
your gym.
Part No.
BAG 79
33A03
1/4" Nyloc Nut
6
33A14
1/4" x 1 3/4" RHSMS
6
33A33
5/16" Nyloc Nut
3
33A45
3/8" x 13/16" Stripper Bolt
3
33B63
3/8" SAE Washer
3
41A82
3" Pulley Wheels
3
33E30
1001 Pt.1230 Painted
3
Locate Bag 79 and check contents as listed:
Assemble Pt.2221 as
per drawing E using
Bag 79.
Description
Qty.
1242
Part No.
Qty.
BAG 81
27A51
1" x 6" Foam Grip
4
41B011
1" Rnd. Int. Cap (Red)
4
Locate Bag 81 and check contents as listed:
Description
Part No.
Qty.
BAG 78
33A51
3/8" Hex Nut
4
33A53
3/8" Nyloc Nut
4
33A573
1001 Hook Bolt
4
41B402
3/8" Thread Cap
4
Locate Bag 78 and check contents as listed:
Description
Assemble two Pt.2228 to Pt.2227
using Bag 78 as in drawing F.
Spin one nut to end of thread
on hook bolt, insert through
Pt.2228 and Pt.2227 and put
nyloc nut on end of hook
bolt. Do not fully tighten yet.
Part No.
BAG 80
33A53
3/8" Nyloc Nut
9
33A47
3/8" x 3 1/2" HH Bolt
6
33A59
3/8" x 4 1/2" HH Bolt
2
33A591
3/8" x 5" HH Bolt
1
41B031
1 1/2" Sq. Int. Cap(Black)
7
41B402
3/8" Thread Cap
7
Description
Qty.
Locate Bag 80 and check contents as listed:
Place Pt.2225 between the two
Pts.2228 and assemble finger
tight using four x 3/8" x 3 1/2"
bolts and four x 3/8" nyloc nuts
as in drawing G.
Install six black internal
caps into Pt.2228 and Pt.2221.
At this point you will need someone to help you.
Attach finger tight
Pt.22241 to Pt.2225 using
one x 3/8" x 4 1/2" bolt and
one x 3/8" nyloc nut (diag.H).
NOTE: The holes that are
the shortest distance from
the end of Pt.22241
should be at the
top of the unit.
Assembly of weights and glide channel:
Open Box No.4 which contains vinyl weights. The flat side
of the weight should be on the bottom and is marked "This
Side Down".
There is a black cap on the
end of each weight and as you
slide the weights onto
Pt.2224 and 22241 make sure
that you alternate the cap
from the left to the right
side.If this is not done properly,
you will have trouble when
installing the weight selector
pin. (Drawing I).
Slide Pt.2250 onto Pt.22241, down to the weights. While
your assistant is holding Pt.22241 install (finger tight)
Pt.2221 in the top of Pt.22241 using one x 3/8" x 4 1/2"
bolt and 3/8" nyloc nut. Continue to hold Pt.22241.
22241
2224
PAGE 4
46/99