YOKOGAWA vigilantplant DM8 Скачать руководство пользователя страница 39

Страница: 39 / 63

<3. INSTALLATION, PIPING AND WIRING>

3-14

IM 12T03A01-02E

< Connection to Density Converter >

The density converter is installed in field or indoors (control room). The connector for passing

through cable should be sealed for air purge. The connector with a ring packing as shown in

Figure 3.26 should be used, or the inlet of metal conduit is filled with silicon sealing compound.

Duct or protective pipe for the cable should be provided to prevent the cable from damage.

Figure 3.26

Packing Gland Type Connector

Figure 3.27 Cable Inlet for Metal Conduit

for Passing through Cable

Take the special cable into the converter from the leftmost inlet and connect the each conductor

to the respective terminals.

<If you selected the /KC option>

If you selected the /KC option, be sure to attach the included ferrite cores to both ends (within 300

mm from the sensor or converter) of the special cable as shown in the figure.

Also, apply the included cable straps to both ends to prevent the ferrite cores from moving.

Cable straps

Ferrite core

Special cable

* Ferrite core attachment range

Within 300 mm

Figure 3.28 Ferrite core attachment

3.4.2

Wiring for Analog Output Signal

Output signal of 4 to 20 mA DC output (load resistance 550Ω or less) and 0 to 1 V DC (load

resistance 250 kΩ or more) are provided. Carry out either or both of wirings as necessary.

Shielded 2-conductor (for one signal) or 4-conductor (for two signals) cable are used for wiring.

For connecting the cable to the converter, remove the sheath of conductor about 50 mm from its

end, and attach a solderless lug for M4 screw omit. The shield of the cable should be grounded at

the receiving unit.
Wiring method (metal conduit and others) is same as that of Section 3.4.1.

5th Edition : Dec. 11, 2015-00

Cable

Converter case

Lock nut

G3/4 screw

Flaxible fitting

Nut

Содержание vigilantplant DM8
































































Результаты поиска

Содержание vigilantplant DM8

Отзывы:

Похожие инструкции для vigilantplant DM8

Бренды по названию

Популярные бренды

YOKOGAWA vigilantplant DM8, Руководство пользователя

Результаты поиска

Содержание vigilantplant DM8

Отзывы:

Похожие инструкции для vigilantplant DM8

Бренды по названию

Популярные бренды