YOKOGAWA TB830D Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 85

YOKOGAWA TB830D Скачать руководство пользователя страница 63

<8. MAINTENANCE>

8-2

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

(1) Set converter maintenance mode to On.

(2) Open valve V4 and perform wash for approximately 30 seconds. (Refer to

Table 3.2 for the

status of the valves in wash.)

Wash while running sample or zero water to avoid splashing With sampling system.

(3) Close valve V4 and open valve V5 for approximately 10 seconds to drain.

(4) Repeat steps (2) and (3) several times according to the degree of contamination.

(5) Close valve V5.

(6) End.

8.2

Cleaning of Flow cell

Wash the inside of the detector with a brush, etc.
(1)  Turn on the maintenance mode.
(2)  Select the draining status. (Table 3.2 for the status of each valve when draining).
(3)  Loosen screw A at the bottom of the detector and open the top of the detector. (Table 8.1).
(4)  When the water in the detector is drained, polish the Flow cell with a soft brush, sponge, etc.

At this time, do not scratch the inside of the detector. Do not splash water on the lens on the

light source section and the light receiving section.

(5) Open Valve V4 and solenoid valve SV2 to feed water and discharge floating dust. At this

time, gradually open valve V4 so that water does not splash water on the lens on the light

source section and the light receiving section.

(6) After the wash is completed, tighten screw A firmly to execute the Zero calibration and Slope

calibration.

(7) End.

Screw A

Flow cell

LIght source

Detector part

Figure 8.1

8.3

Cleaning of Head tank

This section describes the cleaning of the head tank.
(1) Set converter maintenance mode to On.
(2) Open the valves so they are set to drain the tank. Refer to Table 3.2 for the status of each

valve during drainage.

(3) After the water in the head tank is drained off, open the upper cover and wipe the inside of

the tank with a soft brush, sponge, or the like.

«
...
61
62
63
64
65
...
»

Содержание TB830D






















































































Отзывы:

Нет отзывов