YOKOGAWA TB830D Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 85

YOKOGAWA TB830D Скачать руководство пользователя страница 62

<8. MAINTENANCE>

8-1

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

8. MAINTENANCE

This chapter describes the inspection and maintenance required to keep the instrument in good

operating condition.

n

Inspection/Maintenance Items and Intervals

The main inspection/maintenance items and their recommended intervals to keep the instrument

in good operating condition are provided in Table 8.1.
Since the frequency of inspection/maintenance depends on the operating conditions, use the

recommended intervals shown in Table 8.1 as a reference and perform inspection/maintenance

at appropriate intervals.

Table 8.1

Inspection/Maintenance Items and Recommended Intervals

Inspection/Maintenance Item

Recommended Interval Reference

section

Cleaning with tap water

As needed

8.1

Cleaning of Flow cell

Weekly

8.2

Cleaning of head tank

Monthly

8.3

Checking and replacing desiccants

6 months

8.4

Pipe cleaning

6 months

8.5

Lens cleaning

6 months

8.9

Inspection solenoid valve

6 months

8.6

Replacement of zero turbidity filter element

Yearly *1

8.7

LED replacement

3 Years

8.8

Fuse replacement

As needed

8.10

Replacement of the Silicone Tube *2

Yearly

8.11

Checking flow rate (liquid level)

Monthly

8.12

Zero calibration

Monthly

7.4, 7.5

Slope calibration

Monthly

7.6

,

7.7

*1:

This is an interval estimated if tap water used has average turbidity of 0.4 dgrees and runs at a flow rate of 2 L/min.

*2:

With sampling system (-A1, -A2, -A3)

8.1

Cleaning with cleaning water

When Without automatic cleaning (Sampling system:-NN,-A1) is selected, the valve is manually

opened/closed and cleaning is performed.
Wash while running the zero water to avoid splashing the cleaning water.
(1) Set converter maintenance mode to On.
(2) Loosen screw A at the bottom of the detector and open the top of the detector.

(3) Close the valve V1 and open V3 to allow zero water flow.

Open valve V4 gradually to prevent splashing of cleaning water from the Flow cell. With the

valve V4 open, wash for approximately 30 seconds.

(4)  Close the valve V4 and open the valve V5 for about 10 seconds to drain the water.
(5)  Repeat steps (3) and (4) several times, depending on stain severity.
(6)  Close the valve V5.

(7) Close the upper part of the detector and tighten the screw A.

Set the valve to the state at the time of measurement and turn Off the maintenance mode.

Automatic cleaning is performed periodically when With sampling system (Sampling system:-A2,

-A3) is specified. See “4.5 Automatic cleaning/Automatic zero calibration setting”

for automatic

cleaning/automatic zero calibration.

When (Sampling system :-A1) is specified: Cleaning is performed by manually operating the

valve V4 for a wash.

«
...
60
61
62
63
64
...
»

Содержание TB830D






















































































Отзывы:

Нет отзывов