manualshive.com logo in svg

YOKOGAWA TB830D, Руководство пользователя, Страница: 36 / 85

Поделиться
Скачать
YOKOGAWA TB830D Скачать руководство пользователя страница 36

  

< 4. SETTING PARAMETERS >

4-1

IM 12E04B40-02EN

1st Edition : Mar. 08, 2023-00

4.  SETTING PARAMETERS

This section describes how to set up turbidity meter-specific parameters.

Table 4.1 lists the parameters that can be set up from the sensor menu. Table 4.2 lists the 

parameters of “Automatic cleaning/Automatic zero calibration setup” among the parameters that 

can be set up from the converter menu. For further converter menu setup parameters, refer to 

FLXA402T userʼs manual (converter operation).

To go to the Sensor setting menu, refer to 

“5.5  Setting”

. To go to the converter menu, refer to 

section 3.4 in FLXA402T Operation of Converter IM 12A01G01-03EN.

Table 4.1 

Sensor setting

Menu

Parameter

Default

Reference

Measure setting 

Negative value non output

Disable

4.1.1

Turbidity unit select

mg/L

4.1.2

User-defined unit

(blank)

Meas. damping time constant 20.0 sec

4.1.3

Turbidity warning High limit

9999 (*1)

4.1.4

Turbidity warning Low limit

-10.0 (*1)

Air denoising setting

Air denoising function

Disable

4.1.5

Air noise detection value

999.9 (*1)

Air denoising hold time

30 [sec]

Denoising release time

30 [sec]

Cal./Maint. settings

Turbidity value of check tool 

90.0 (*1)(*3) 4.2.1

Maint. damping time constant 6 [seconds]

4.1.3

Zero shift value 

0.0

4.2.2

Correction factor

1.0

Stability check allowable width (*2)

4.2.3

Stability checking time

10 [sec]

Stability check limit time

1.0 [minutes]

Wash/Cal. box

Disable (*3)

4.2.4

Calibration setting others

Zero

(*2)

4.2.5

Slope

100.0[%]

Sens.factor

(*2)

Linearize  

table 

point 1. X value

(*2)

Y value

(*2)

point 2. X value

(*2)

Y value

(*2)

point 3. X value

(*2)

Y value

(*2)

point 4. X value

(*2)

Y value

(*2)

point 5.

X value

(*2)

Y value

(*2)

point 6. X value

(*2)

Y value

(*2)

*1: 

Depend on the configured unit of turbidity

*2: 

Value is preset factory default. After initialization, set each value to default.

*3: 

The factory default setting and default may differ. Check the factory default setting.

Содержание TB830D






















































































Отзывы:

Нет отзывов