manualshive.com logo in svg

YOKOGAWA PH200, Инструкция по эксплуатации

Поделиться
Скачать
YOKOGAWA PH200 Скачать руководство пользователя страница 42

IM 12B6C2-E-H

38

8. CLASSIFICATION

8-1. Cenelec

Any shunt zenerdiode safety barrier or supply unit or isolated repeater certified by BASEEFA or any EEC approved certification body to 
[EEx ia] IIC or [EEx ib] IIC where the output current is limited in a different way and not exceeding the follwoing characteristics:
Vmax.out = 22 V en Imax.out = 85 mA
such as (but not limited to): 

Type

: Camille Bauer Sineax 84-2B1-511

Sineax 89-2B1-511

(P.T.B. Cert. Ex-81/2044X)

of

SYSTEM CERTIFICATE
EXA200 INSTRUMENTS
BASEEFA NR Ex 892380

A)

1 ORP-sensor, 
such as (but not limited to)

SM29-PT8

or
A)

1 PH-glass sensor,

SM21-AG4

such as (but not limited to)

SM21-AG6

plus

SM21-TL4

B)

1 reference sensor

SR20-AC22

such as (but not limited to)

SR20-AP24

or

SR20-AL32

AB) 1 combined sensor

SC21-AGP24

such as (but not limited to)

SC21-ASP24

plus
C)

1 temperature sensor

SM60-Pt100

such as (but not limited to)

SM60-Pt1000

These are all passive sensors to be regarded as “simple appara-
tus” i.e. devices which comply with clause 1.3 van EN 50014.

Ex-classification: EEx ib [ia] IIC T4 
Zone 0 or 1

Zone 1

ZONE 1 

OR 

ZONE 2

Connecting cables
such as (but not limited to):
WU20-PC5

WU20-PC2

WU20-PC10

K1220 EM

WU-LT2

pH 200 S
Vout     

= 14.4 V max.

Iout     

= 3.6 mA max.

C ext   

= 1300 nF max

L ext    

= 1000 mH max.

BASEEFA Nr. Ex 89C2379

SC 200 S
Vout     

= 14.4 V max.

Iout     

= 72.8 mA max.

C ext    

= 1300 nF max

L ext    

=  8.0 mH max.

BASEEFA Nr. Ex 89C2379

NON HAZARDOUS AREA

Certified Barrier with electronic current limitation and the following characteristics:
Vmax.out = 31.5 V, 

Imax.out = 35 mA, 

Pmax.out = 1.1 W

Type : Yokogawa Bard 400 (BASEEFA Cert. Ex 84B2257X)

Any shunt zenerdiode safety barrier certified by BASEEFA or any EEC approved certification body to [EEx ia] IIC or [EEx ib] IIC where the
output current is limited by a resistor “R” directly in the output line such that Imax.out = Vmax.out / R and not exceeding the follwoing 
characteristics:
Vmax.out = 28 V; 

Imax.out = 93.3 mA 

Pmax.out = 8.66 W.

such as (but not limited to):
Type:

MTL 728
MTL 788

(BASEEFA Cert. Ex 832452)

MTL 788 R
Stahl 8981/31-280/085/00 (P.T.B. Cert. Ex-78/2007X)

of

1 

conductivity sensor with

SC41-SP34

integral temperature sensor 

SC49-FP08

such as (but not limited to)

SC41-SP24
SC41-EP14
SC41-EP04

These are all passive sensors to be regarded as “simple appara-
tus” i.e. devices which comply with clause 1.3 van EN 50014.

Connecting cables
such as (but not limited to):
WU40-LH18

WU40-LH2

WU40-LH5

11  12  14  13  17  15  16

11  12  14  13  17  15  16

G  -  +

G  -  +

Содержание PH200

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды