background image

 

 

<4.  Operation>

4-1

IM 02M04B01-01EN

4.  Operation

Controller is available either with or without 

Automatic-Manual Transfer System.  The following 

covers the operation of controller having that 

system.

4.1  Automatic-Manual Transfer 

System

The automatic-manual transfer system consists 

of a regulator, a sensitive balance indicator, and 

a transfer switch.  The system permits switching 

between manual and automatic control without 

upsetting the process.
The illustration below shows the components that 

are concerned with the transfer system.

Set point index

Measurement pointer

Output gauge

Auto-man switch
Balance indicator

Regulator

Set point knob

F0401.ai

1

2

3

1.  To Transfer from Manual to Automatic Control

 

Slowly turn set point knob (or adjust remote set 

point, if present) to move balance indicator ball 

to within central portion of tube (not up against 

either end).  Then turn switch to automatic (A).

2.  To Transfer from Automatic to Manual Control

 

Turn regulator slowly to move balance indicator 

ball to within central portion of tube (not up 

against either end).  Turn regulator so that top 

of knob moves in direction that ball is to move.  

Then turn switch to manual (M).  Valve can now 

be controlled with regulator.

3.  Shutoff for air to automatic control section 

(controller can still be operated manually).

4.2  Putting into Operation

1.  Make sure that measuring system is properly 

installed and operating.

2.  Set control dial so that index points to desired 

control action (output either increases or 

decreases with increasing measurement).

F0402.ai

Control dial

Stop

Latch

Index

 

With latch in lowered position (as shown), 

control dial cannot be accidentally rotated to 

area of reverse control action.

F0403.ai

Stop

Latch

 

To reverse control action, push up latch and 

rotate dial so that latch is on other side of stop, 

then push down latch.

 

 

*  Control dial is set to “Increase” action for pressure 

measurement and to “Decrease” action for 

temperature measurement.

Содержание MC43













































Отзывы: