YOKOGAWA MC43 Скачать руководство пользователя страница 12

Страница: 12 / 44

<3. Installation>

3-2

IM 02M04B01-01EN

Panel Mounting Procedure

(1) Loosen four screws and remove the mounting

hardware.

(2) Put the instrument in the panel and reassemble

the mounting hardware.

(3) Using two clamp screws, fix the instrument. For

panel mounting, the bolts, bracket, etc. are not

necessary.

F0303.ai

Washer

Screw

Mounting hardware

Clamp screw

Figure 3.3

Panel Mounting.

Surface Mounting Procedure

(1) Use M5 (5mm) or No. 10-24UNC screws.

(2) In this case, the bolts, bracket, etc. are not

necessary.

Figure 3.4

Surface Mounting.

3.2 Air Supply and Output

Piping

F0305.ai

If output pulsates, add small

capacity tank (approx. 500cc)

to output line.

Shutoff valve

Regulator

3/8-inch Tubing to

control valve

Filter

Air

supply

NOTE

• Air supply must be regulated at a fixed

pressure 1.4 kgf/cm

or bar, 140 kPa, or 20

psi.

• Transmitter uses 0.5 Nm

/h of air in normal

operation.

• Air must be clean and dry. Blow out filter

regularly.

• Transmission line must be free of leaks.

Содержание MC43













































Результаты поиска

Содержание MC43

Отзывы:

Похожие инструкции для MC43

Бренды по названию

Популярные бренды

YOKOGAWA MC43, Руководство пользователя

Результаты поиска

Содержание MC43

Отзывы:

Похожие инструкции для MC43

Бренды по названию

Популярные бренды