YOKOGAWA FA-M3V e-RT3 Plus, Руководство по оборудованию

Страница: 117 / 274

A2-83
IM 34M06C11-01E
(30) F3WD64-3P/F3WD64-4P Input/Output Modules (with short-circuit
protector)
 Input Block
Item F3WD64-3P F3WD64-4P
Input type DC voltage
Number of points 32 (terminal Nos. 01 - 32)
Common line type 8 points/common
Isolation method Photocoupler isolation
Withstanding voltage
1500V AC for one minute between the group of terminals for external
connection and the internal circuit
Rated input voltage
(
operating voltage range
)
24V DC
(
20.4 to 26.4V DC
)
12V DC
(
10.2 to 13.2V DC
)
Rated input current 4.1mA/point (24V DC) 4.1mA/point (12V DC)
Input impedance 5.9kΩ 2.9kΩ
Operating
voltage/current
ON 16.0V DC min. 3.2mA min. 8.0V DC min. 2.6mA min.
OFF 5.8V DC max. 0.9mA max. 3.4V DC max. 1.0mA max.
Response time
OFF
→
ON
Input sampling time can be specified for 4 steps: Always (0μs), 62.5μs, 250μs,
and 1ms.
*1
ON → OFF
Input sampling time can be specified for 4 steps: Always (0μs), 62.5μs, 250μs,
and 1ms.
*1
Interrupt None
Withstanding voltage
1500V AC for one minute between the group of terminals for external
connection and the internal circuit
Input display *2
Lit when input is on (Input or output status indication can be selected using a
switch.)
Dissipating current 170mA (5V DC) (for input and output)
External connection One 40-pin connector
Weight 120g (for input and output)
Maximum ratio of inputs turned on
simultaneously
60% 100%
*1: These values are applicable when using the module with CPU module using F3SP22, F3SP28, F3SP38, F3SP53,
F3SP58, F3SP59, F3SP66, F3SP67, F3SP71 or F3SP76 module. If other CPU modules are used, the values for
OFF

ON and for ON

OFF are 1.0 ms and 2.5 ms max. respectively. The actual response time is obtained by
adding about 100

s for OFF

ON and about 300

s for ON

OFF to the specified value.
If input interrupt is to be used, set the input sampling time to 62.5μs or more.
*2: The contact operation of the output block of the circuit and the LED display operate independently and thus may be
inconsistent in the event of an error.
 Output Block
Item F3WD64-3P F3WD64-4P
Output type Transistor contact (sink type)
Number of points 32 (terminal Nos. 33 - 64)
Common line type 8 points/common
Isolation method Photocoupler isolation
Withstanding voltage
1500V AC for one minute between the group of terminals for external
connection and the internal circuit
Rated load voltage
(Operating load voltage range)
24V DC
(20.4 to 26.4V DC)
12V DC
(10.2 to 13.2V DC)
Maximum load current 0.1A/point, 0.4A/common line
Response time
OFF
→
ON 1ms max.
ON
→
OFF 1ms max.
ON voltage 0.5V DC max.
Off-time leak current 0.1mA max.
Protection circuitry Short-circuit Controlled short-circuit current
Overheat Output shutdown
Surge protector *3 Active clamp
Fuse None
Output status when the program
stops HOLD/RESET *4
When a sequence CPU module is used:
Default: RESET
Can be set globally on a module-by-module basis
*5
When a BASIC CPU module is used:
No setting function
The status is always HOLD
External power supply 24V DC, 55mA 12V DC, 55mA
Output status display *6
Lit when output is on (Input or output status indication can be selected using
a switch.)
Dissipating current 170mA (5V DC) (for input and output)
External connection One 40-pin connector
Weight 120g (for input and output)