YOKOGAWA Dpharp EJ 510 Series Скачать руководство пользователя страница 7

Страница: 7 / 58

<1. Introduction>

1-3

IM 01C25F01-01E

1.1 Safe Use of This Product

For the safety of the operator and to protect the

instrument and the system, please be sure to follow

this manual’s safety instructions when handling this

instrument. If these instructions are not heeded,

the protection provided by this instrument may be

impaired. In this case, Yokogawa cannot guarantee

that the instrument can be safely operated. Please

pay special attention to the following points:

(a) Installation

WARNING

• The instrument must be installed by an

expert engineer or a skilled personnel. The

procedures described about INSTALLATION

are not permitted for operators.

• In case of high process temperature, care

should be taken not to burn yourself because

the surface of body and case reaches a high

temperature.

• The instrument installed in the process is

under pressure. Never loosen the process

connection to avoid the dangerous spouting

of process fluid.

• During draining condensate from the

pressure detector section, take appropriate

care to avoid contact with the skin, eyes

or body, or inhalation of vapors, if the

accumulated process fluid may be toxic or

otherwise harmful.

• When removing the instrument from

hazardous processes, avoid contact with the

fluid and the interior of the meter.

• All installation shall comply with local

installation requirement and local electrical

code.

(b) Wiring

WARNING

• The instrument must be installed by an

expert engineer or a skilled personnel. The

procedures described about WIRING are not

permitted for operators.

• Please confirm that voltages between the

power supply and the instrument before

connecting the power cables and that the

cables are not powered before connecting.

(c) Operation

WARNING

• Wait 5 min. after power is turned off, before

opening the covers.

• Do not open the cover in wet weather or

humid environment. If the cover is opened,

stated enclosure protection is not applicable.

(d) Maintenance

WARNING

• Please do not carry out except being written

to maintenance descriptions. When these

procedures are needed, please contact

nearest YOKOGAWA office.

• Care should be taken to prevent the build

up of drift, dust or other material on the

display glass and name plate. In case of its

maintenance, soft and dry cloth is used.

(e) Explosion Protected Type Instrument

WARNING

• Users of explosion proof instruments should

refer first to section 2.4 (Installation of an

Explosion Protected Instrument) of this

manual.

• The use of this instrument is restricted to

those who have received appropriate training

in the device.

• Take care not to create sparks when

accessing the instrument or peripheral

devices in a hazardous location.

(f) Modification

WARNING

Yokogawa will not be liable for malfunctions or

damage resulting from any modification made to

this instrument by the customer.

(g) Product Disposal

The instrument should be disposed of in

accordance with local and national legislation/

regulations.

Содержание Dpharp EJ 510 Series



























































Результаты поиска

Содержание Dpharp EJ 510 Series

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA Dpharp EJ 510 Series, Руководство пользователя

Результаты поиска

Содержание Dpharp EJ 510 Series

Отзывы:

Бренды по названию

Популярные бренды