O P E R AT I O N
INSTRUCTION
Made
in
China
Thank you for purchasing this product. Please
read the manual carefully before operating
&
keep this manual for future reference.
The company reserves the right to improve
&
upgrade products, product specifications
&
design are subject to change without notice.
STATEMENT:
This product should not be thrown in the garbage. In accordance with the
European directive 2012/19/EU, electronic equipment at the end of their life
must be collected & returned to an authorized recycling facility. Este producto
no debe desecharse en la basura. De acuerdo a la directiva europea 2012/19/EU,
los equipos electrónicos al final de su vida se deberàn recoger y trasladar
a una planta de reciclaje autorizada.
Dieses Produkt sollte nicht mit dem
Hausmüll entsorgt werden. In Übereinstimmung mit der europäischen Richtlinie
2012/19/EU müssen elektronische Geräte am Ende ihrer Lebensdauer
eingesammelt und einem autorisierten Recyclingbetrieb zugeführt werden.
English
SPECIFICATION
01
02
03
04
04.07.03.370
929d5
PORTABLEDESOLDERINGIRON
Controlunitdimensions
Operatingambienttemperature
Nozzlediameter
L265xW35xH27mm±5mm
0℃
〜
40℃/32℉
〜
104℉
Φ
1
.
2mm
I. APPLICATIONS
II. PART LIST
Thisunitissuitablefordesoldering&specializeddesolderingapplicationsonthrough-hole
componentsandotheroperation.Thisisespeciallysuitablefordesolderingthrough-hole
componentswithmultiplepins(forexample:LCDscreens,nixietubes,integratedcircuits/
microchips,socketpinsandmore).
1. Desoldering Nozzle (Consumable Part)
2. Tin Storage Tube
3. Desoldering Button
4. Piston Rod
5. Power Cord
6. Heating Indicator
7. Locking Screw (Heating Element)
1
2
3
4
5
6
7
1. Connect the desoldering iron’s power cord to
an electrical outlet, and the heating element
will begin heating up.
2. Allow the desoldering iron to preheat for appr-
oximately 3 to 5 minutes, then, push down the
piston rod.
3. Cover the component's pin with the desolderi-
ng nozzle, and melt the solder joint complete-
ly. Then, press the desoldering button to extr-
act the solder completely.
4. When the operation is complete, DISCONNECT
the power cord.
NOTE: When using the desoldering nozzle for the
first time, coat the nozzle with a new layer of
solder(we recommend using rosin core solder) to
prevent oxidization.
III. OPERATION
IV. MAINTENANCE & PRECAUTIONS
CAUTION:
A. Melt the solder completely before pressing the de-
soldering button.
B. If there are solder remains inside the PCB’s hole, r-
esolder. Then, repeat the desoldering procedures.
C. If the component’s pin is stuck on the sidewall ins-
ide the hole, and you are unable to extract the sol-
der completely. Add solder to resolder, then, use
the desoldering nozzle to melt the solder joint co-
mpletely. Move the nozzle back-and-forth, and get
the component’s pins moving together with the n-
ozzle. When the component’s pinsare no longer in
contact with the sidewall of the hole, press the de-
soldering button to extract the solder completely.
D. Clean the tin storage tube regularly to prevent in-
effective desoldering caused by the over accumul-
ation of scrap solder.
1. If a layer of oxidization forms on the surface of
the desoldering nozzle, a misconception can be
