39
40
10. Wireless functions
1.Frequency: 2.412-2.462 GHz
Equivalent isotropic radiated power: Antenna gain＜10dBi≤100mW or≤20dBm
Maximum power spectral density: Antenna gain＜10dBi≤10dBm/MHz(EIRP) Carrier
Band emission power:( outside 2.412-2.462 GHz band) ≤-80dBm/Hz(EIRP)spurious emission
(radiation) power(Corresponding to a carrier other than ± 2.5 times the channel bandwidth)≤
-36dBm/100kHz(30-1000MHz)≤-33dBm/100kHz（2.412-2.462 GHz）≤-40dBm/1MHz
(other 1-12.75GHz)
frequency tolerance: 20ppm
2.Do not use external antennas or other transmitting antennas.
3. Please stop using the camera immediately if you notice that you are interfereing
with other legal radio communications. You should take measures to remove the
intereference before you use the camera again.
4.Please be advised that the radio waves coming from the camera may interefere
with other industral/scientific/medical equipments.
5.Please do not use the camera on the plane or near the airport.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
MPE Requirements
To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the
antenna of this device and persons during device operation.To ensure compliance, operations at closer than this distance is
not recommended.
Les antennes installées doivent être situées de facon à ce que la population ne
puissey être exposée à une distance
de moin de 20 cm. Installer les antennes de facon à ceque le personnel ne puisse approcher à 20 cm ou moins de la
position centrale de l’antenne. La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’
au
moins 20 cm des personnes pendant son functionnement.
This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio
pour lé
' metteur par Industrie Canada. Dans le but de réduire les
radioélectriqueà
l 'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de
l'intensité nécessaire à l'établissement
peut fonctionner avec une antenne
d'un type et d'un gain maximal (ou inférieur) approuvé
risques de brouillage
sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
d'une communication satisfaisante.
