Yenista Optics OSICS Скачать руководство пользователя страница 62

Страница: 62 / 252

Using the OSICS BKR Module

OSICS User Manual

7.3

Setting the BKR Wavelength/Frequency

Subject

The

Set

menu enables you to set the reference wavelength. Each module is factory-

calibrated at different wavelengths depending on the module version (SMF or PMF): see

section

OSICS BKR Technical Specifications, p. 57

Procedure

Access the BKR

Unit Setup

menu (see section

Accessing an OSICS Module Setup

Menu, p. 33

Turn the rotary knob to put the cursor before the

Set

menu and press the knob.

The

Set Wavelength

Set Frequency

menu appears and displays the current value of

wavelength or frequency according to the selected unit.

Figure 34: BKR Unit Setup – Set Wavelength menu

Turn the rotary knob to put the cursor before the wanted value and press it to

validate your selection.
The

Unit Setup

menu is automatically displayed and the wavelength/frequency value

is now set.

Main

EXIT

BKR Unit Setup - Set Wavelength

ESCAPE

▲

Wavelength :

1550 nm

1300 nm

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды