Yenista Optics OSICS Скачать руководство пользователя страница 216

Страница: 216 / 252

Using the OSICS TLS-50 Module

216

OSICS User Manual

14.5.2 Selecting the SBS Rate

Subject

The OIF recommended values for SBS rate (for amplitude and frequency modulation) are

given in section

Setting the SBS Suppression Mode, p. 214

Procedure

Access the TLS-50

Unit Setup

menu (see section

Accessing an OSICS Module Setup

Menu, p. 33

Expand the

SBS Suppression

menu and enter the

SBS Rate

sub-menu.

The sub-menu appears and displays the current frequency deviation.

Figure 163: TLS-50 Unit Setup – SBS FM sub-menu

Modify the value as follows:
a. Turn the rotary knob to put the cursor under the digit you want to modify and

press the knob to highlight it.

b. Turn the knob clockwise to increase the value or anticlockwise to decrease it and

press the knob to validate the selected digit.

c. Perform steps a. and b. again with the other digit to modify.
d. Turn the rotary knob clockwise to put the cursor under

ENTER

and press the

knob to validate the new value.

The SBS rate is set and the TLS-50

Unit Setup

menu is automatically displayed.

14.5.3 Selecting the SBS Waveform

Subject

You can choose between triangular or sinusoidal shape, whatever the selected

modulation mode. The OIF recommended values for waveform (for amplitude and

frequency modulation) are given in section

Setting the SBS Suppression Mode, p. 214

Procedure

Access the TLS-50

Unit Setup

menu (see section

Accessing an OSICS Module Setup

Menu, p. 33

Expand the

SBS Suppression

menu and enter the

SBS Waveform

sub-menu.

The sub-menu appears and displays the current state of the SBS Suppression.

Main

EXIT

TLS Unit Setup - SBS Rate

ESCAPE

▲

010 kHz

SBS Rate :

Select a new value.

ENTER

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды