Yenista Optics OSICS Скачать руководство пользователя страница 210

Страница: 210 / 252

Using the OSICS TLS-50 Module

210

OSICS User Manual

14.4

Setting the Optical Emission Wavelength/Frequency

14.4.1 Specifying the Optical Emission Wavelength/Frequency

Subject

The following procedure explains how to set the emission wavelength or optical

frequency of the OSICS TLS-50 module according to its specifications.

Before Starting

•

Set the spectral unit from the OSICS Mainframe

Main Setup

menu (see section

Selecting the Spectral Unit for all Installed Modules, p. 39

). You cannot set the spectral

unit of an individual module.

Procedure

Access the TLS-50

Unit Setup

menu (see section

Accessing an OSICS Module Setup

Menu, p. 33

Turn the rotary knob to put the cursor before the

Set

menu and press the knob.

The

Set

menu appears and displays the current channel and the corresponding

emission wavelength or frequency.

Figure 158: TLS-50 Unit Setup – Set Wavelength/Frequency menu

Modify the wavelength/frequency value channel value as follows:
a. Turn the rotary knob to put the cursor under the digit you want to modify and

press the knob to highlight it.

b. Turn the knob clockwise to increase the value or anticlockwise to decrease it and

press the knob to validate the selected digit.

c. Perform steps a. and b. again with the other digits to modify.
d. Press the

ENTER

control button to validate the new wavelength and to go back

to the

Unit Setup

menu.

The

Unit Setup

menu is automatically displayed and the wavelength/frequency value

of the module is now modified (according to the module limits).

Main

ENTER

TLS Unit Setup - Set

ESCAPE

▲

Channel:

CH = 01 (1565.701 nm)

Modify the value.

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды