Yenista Optics OSICS Скачать руководство пользователя страница 162

Страница: 162 / 252

Using the OSICS SWT APC Module

162

OSICS User Manual

d. Turn the rotary knob clockwise to put the cursor under

ENTER

and press the

knob to validate the new wavelength value.

The

Unit Setup

menu is automatically displayed and the wavelength/frequency value

of the module is now modified (according to the module limits).

12.7.2 Step-adjusting the Wavelength/Frequency Value of the Module

Subject

The following procedure explains how to modify the wavelength/frequency of the

module step by step using the increment defined in the

Set Step

sub-menu.

You can define a valid step value within the range 00.00–50.00 nm. If you use two non-

adjacent T100 or ECL, check that the step is high enough.
The starting wavelength is the value originally defined in the

Set

menu (see section

Specifying the Optical Emission Wavelength/Frequency, p. 161

Procedure

Access the SWT APC

Unit Setup

menu (see section

Accessing an OSICS Module Setup

Menu, p. 33

Expand the

Step

menu and enter the

Set Step

sub-menu.

The

Set Step

sub-menu appears and displays the current value of the wavelength/

frequency step in nm or GHz .

Figure 119: SWT APC Unit Setup – Set Step sub-menu

Modify the step value as follows:
a. Turn the rotary knob to put the cursor under the digit you want to modify and

press the knob to highlight it.

b. Turn the knob clockwise to increase the value or anticlockwise to decrease it and

press the knob to validate the selected digit.

c. Perform steps a. and b. again with the other digits to modify.
d. Turn the rotary knob clockwise to put the cursor under

ENTER

and press the

knob to validate the new wavelength value.

The

Unit Setup

menu is automatically displayed.

To increase or decrease the wavelength/frequency value defined in the

Set

(see section

Specifying the Optical Emission Wavelength/Frequency, p. 161

) step by

step, expand the

Step

menu and put the cursor before the

Step +

Step -

sub-

menus and press the knob to step-adjust the value.
While the module is updating the wavelength/frequency, the message

Moving…

appears along with the new wavelength/frequency value after step-change.

Repeat step 4. until the wanted wavelength/frequency is reached.

Main

EXIT

Unit Setup - Set Step (nm)

ESCAPE

▲

Step:

01.00 nm

ENTER

Modify the value.

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды