2
Functions and address set of Digital Indicate Board:
This control display menu is specially designed for multi-types of
moving-heads. It enables the control modes of several funtions and is easy to
control. The corresponding menu choices will not work if there is no motion for
some types of moving-heads.
Reposition Function: press the button
“
down
”
or
“
up
”
. When
“
rest
”
shows up,
press
“
enter
”
. Reposition is finished when
“
rest
”
comes out.
DMX512(Address set): this is for you to change the address number., Press
the button
“
ESC
”
once or more than once until it displays
“
A.001
”
. Press the
button
“
enter
”
, then the word
“
A
”
disappears followed behind 3 figures. Use
“
up
”
and
“
down
”
to set the address codes. Press
“
enter
”
.
Self-walk and sound control set
Press
“
up
”
or
“
down
”
until it shows
“
audi
”
. Press
“
enter
”
to show
“
off
”
or
“
on
”
.
Then press
“
down
”
or
“
up
”
again. Choose
“
off
”
or
“
on
”
(
“
off
”
is for self-walk.
“
on
”
is for sound control.) After finishing the choice, press
“
enter
”
back to
“
audi
”
.
Press
“
down
”
or
“
up
”
to show
“
test
”
. Press
“
enter
”
again to show
“
nod.1
”
. Press
“
enter
”
again, indicating
“
run
”
. Then the machine will work as set above (
“
off
”
for
self-walk and
“
on
”
for sound control.) When sound control is in use, green led
will flash according to the frequency of the sound control.
Master/slave In-phase control
Main lighting set: Press
“
down
”
or
“
up
”
to indicate
“
test
”
. Press
“
enter
”
again
to show
“
nod.1
”
. Press
“
down
”
or
“
up
”
to show
“
nast
”
. Press
“
enter
”
again to
show
“
off
”
or
“
on
”
. Press
“
down
”
or
“
up
”
to choose
“
off
”
or
“
on
”
with
“
on
”
for the
main lighting. Then press
“
enter
”
back to
“
nast
”
. Press
“
down
”
or
“
up
”
ot show
Installation:
make sure there is no highly flammable and explosive objects(decorations)
within 0.5m while installing the machine.
Please ensure the machine is installed in a location with adequate ventilation
and no ventilation slots are blocked.
Please keep the machine away from rain, moisture and humidity. Cut off
power before opening the outer shell.
You only need to open the back board to replace the bulb.
Connect the signal line packed with the machine to the controller to work the
machine.
Instructions for using the machine:
Before turning on the machine, please check if power and voltage is normal.
You are advised to use 220V voltage regulator to supply power if the voltage
fluctuates vastly in your area.
The machine complies to lighting of the first-grade protection. Therefore, the
yellow and green line must be correctly earthed and maintained by technicians.
Do not touch the outer shell when the machine is in use.
Please restart the machine after 20 minutes until the bulb cooled well
because it is gas discharge bulb.
The interior parts of the machine (e.g. trigger) must be bought from the
manufacturer.
The power line should be correctly earthed.
When using the controller, be sure that there is not disturbing source around
it(e.g. wireless interphone, high-frequency radiation source)
