Yealink Yealink SIP-T48G Скачать руководство пользователя страница 276

Страница: 276 / 319

Microsoft Lync Edition Administrator’s Guide for SIP-T2_Series and T4_Series IP Phones

264

3xx Response

Supported

Notes

301 Moved Permanently

Yes

302 Moved Temporarily

Yes

4xx Response—Request Failure Responses

4xx Response

Supported

Notes

400 Bad Request

Yes

401 Unauthorized

Yes

402 Payment Required

Yes

403 Forbidden

Yes

404 Not Found

Yes

405 Method Not Allowed

Yes

406 Not Acceptable

407 Proxy Authentication
Required

Yes

408 Request Timeout

Yes

409 Conflict

410 Gone

411 Length Required

413 Request Entity Too Large

414 Request-URI Too Long

Yes

415 Unsupported Media Type

Yes

416 Unsupported URI Scheme

420 Bad Extension

421 Extension Required

423 Interval Too Brief

Yes

480 Temporarily Unavailable

Yes

481 Call/Transaction Does Not
Exist

Yes

482 Loop Detected

Yes

483 Too Many Hops

484 Address Incomplete

Yes

Содержание Yealink SIP-T48G
































































































































































































































































































































Результаты поиска

Содержание Yealink SIP-T48G

Отзывы:

Yealink Yealink SIP-T48G, Руководство администратора, Страница: 276 / 319

Результаты поиска

Содержание Yealink SIP-T48G

Отзывы: