manualshive.com logo in svg

Yealink VC110, Руководство администратора

Yealink VC110 - отличное решение для видеоконференций в вашем офисе. Для быстрого начала работы с устройством, скачайте бесплатное Руководство по быстрому старту и руководство пользователя на manualshive.com. Удобная инструкция поможет вам освоить функционал VC110 и начать эффективное взаимодействие с коллегами.

Поделиться
Скачать
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

196 

To configure LDAP via web user interface: 

1.

 

Click on Directory->LDAP. 

2.

 

Enter the values in the corresponding fields. 

3.

 

Select the desired values from the corresponding pull-down lists. 

 

4.

 

Click Confirm to accept the change. 

The VC110 video conferencing endpoint maintains call history lists of All Calls, Missed 
Calls, Placed Calls and Received Calls. Call history lists supports up to 100 entries. You 
can view the call history, place a call or delete an entry from the call history list. You can 
view the call history and place a call from the call history list via web user interface or 
the remote control, but you can delete call history only via web user interface. 

History record feature is enabled by default. If it is disabled, the call history won‘t be 
saved. For more information, refer to 

History Record 

on page

 133

. 

 

 

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Panasonic SC-AK48 Service Manual preview
SC-AK48
Бренд: Panasonic Страницы: 104
Panasonic SC-AK48 Operating Instructions Manual preview
SC-AK48
Бренд: Panasonic Страницы: 32
HandyTrac Key Control Easy Manual Installation And Operation preview
Key Control
Бренд: HandyTrac Страницы: 14
Idemia SIGMA Series Quick User Manual preview
SIGMA Series
Бренд: Idemia Страницы: 29
IN-COMMAND NCSP35CM Installation And Operation Manual preview
NCSP35CM
Бренд: IN-COMMAND Страницы: 47
Clatronic AR 829 DVD Instruction Manual preview
AR 829 DVD
Бренд: Clatronic Страницы: 38
GRAUPNER MC-22S Programming Manual preview
MC-22S
Бренд: GRAUPNER Страницы: 180
Audiovox Prestige P-98 Owner'S Manual preview
Prestige P-98
Бренд: Audiovox Страницы: 35
Cistermiser sensazone SZ/ASK Installation Manual preview
sensazone SZ/ASK
Бренд: Cistermiser Страницы: 16
Logitech LifeSize Unity 500 Quick Reference Card preview
LifeSize Unity 500
Бренд: Logitech Страницы: 3
Zenith F-986 Installation And Operating Manual preview
F-986
Бренд: Zenith Страницы: 20
Polycom HDX Desktop Systems Quick Start Manual preview
HDX Desktop Systems
Бренд: Polycom Страницы: 2
Leviton Lumina LU20S-DNW Installation Instructions preview
Lumina LU20S-DNW
Бренд: Leviton Страницы: 3
Bosch DCN-CONCM Concentus Quick Reference Manual preview
DCN-CONCM Concentus
Бренд: Bosch Страницы: 2
Bosch DCN Next Generation 4.41 Release Notes preview
DCN Next Generation 4.41
Бренд: Bosch Страницы: 14
Bosch DCN-CON Concentus Delegate Unit Quick Reference Card preview
DCN-CON Concentus Delegate Unit
Бренд: Bosch Страницы: 2
Bosch CCS 900 Ultro Installation And Operating Manual preview
CCS 900 Ultro
Бренд: Bosch Страницы: 46
Bosch B426 Installation And Operation Manual preview
B426
Бренд: Bosch Страницы: 38

Бренды по названию

Популярные бренды

Загрузить еще бренды