YATO 5906083006036, Оригинальное руководство пользователя, Страница: 17 / 84

17
O R I G I N A L I N S T R U C T I O N S
GB
During operation, the cutting element must be constantly monitored. Do not carry out the cut in places which are remaining out
of sight.
Before you start your works, you should carefully inspect the work place, remove any loose branches and remnants of previous
cutting.
When you work you should use regular breaks. The device, during its operation, emits noise and vibration, that affect the equip-
ment operator. The use of regular breaks and personal protective equipment such as gloves, hearing protection, and eye protec-
tion can reduce the impact of the device operation on the operator’s condition..
You should start the work being healthy and in good shape. In the event of nausea, headache, visual disturbances (eg. reduced
field of vision), hearing problems, dizziness you should immediately stop working with the device.
Tall grass should be cut gradually from the top, this will reduce the risk of winding up of the cut grass on the line spool.
Try to cut grass only by the end of the line, this will reduce the risk of winding up of the cut grass on the line spool.
If during the operation any element of grass trimmer or guard becomes damaged or deformed, you should replace it or fix it before
the start of device operation.
Safety recommendations for battery loading
Attention! Before loading may start make sure the body of the charger, the cable and the plug are not broken or damaged. It
is prohibited to use a damaged loading dock and charger! For the purpose of loading batteries only the charging dock and the
charger provided may be used. Using another charger may be a cause of fire or damage the tool. Batteries may be charged only
in a dry room, protected from unauthorised persons, particularly children. Do not use the charging dock and the charger without
permanent supervision of an adult! If it is necessary to leave the room where loading is taking place, it is required to disconnect the
charger from the mains, removing the charger from the mains socket. In case when smoke comes out of the charger, or a strange
smell is emitted, etc., it is required to immediately remove the plug of the charger from the mains socket!
The drill and automatic return screwdriver is provided with an unloaded battery, so before work may commence, it is required
to charge it following the procedure below, using the charger and charging dock provided. Li-ION batteries do not show the so
called “memory effect”, so it is allowed to charge them at any moment. However, it is recommended to discharge them during
normal work, and then load them to their full capacity. If due to the nature of the task it is not possible to do so each time, then it
is required to do it at least from time to time. Under no circumstances is it allowed to discharge the batteries short-circuiting the
electrodes, since this would cause irreversible damage! It is also prohibited to check the load of the batteries, short-circuiting the
electrodes for sparking.
Storage of the battery
In order to prolong the life of the battery, it is required to provide adequate storage conditions. The batteries can go through ap-
proximately 500 „loading - discharging” cycles. The battery must be stored between 0 and 30°C, at the relative humidity of 50%. In
order to store the battery for a prolonged period, it is required to charge it to approximately 70% of its capacity. In case of prolonged
storage, it is required to recharge the battery once a year. Do not permit excessive discharging of the battery, since this would
reduce its life and may cause irreversible damage.
During storage, the battery will be gradually unloading due to leakage conductance. The process of automatic unloading depends
on the temperature of storage, since the higher the temperature, the fastest the process. In case of incorrect storage of batteries,
there is a danger of electrolyte leakage. In case of leakage, it is required protect the leakage with neutralizing agent. In case of
contact of electrolyte with the eyes, it is required to rinse the eyes abundantly, and then immediately seek medical assistance. It
is prohibited to use a tool with a damaged battery.
In case the battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the
tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third
parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport
of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Charging the battery
Attention! Before charging you should disconnect the charger from the mains by unplugging the power supply from the mains. In
addition, you should clean the battery and its terminals of dirt and dust with a soft, dry cloth.
Disconnect the battery from the tool.
Insert the battery in the charger socket (XIV),
The charging station has two LEDs, green and red. They show the status of operation:
- the red LED lights up - the charging station connected to the power supply,
- the green LED lights up - the battery is charged,
- the red LED lights up, a green LED is flashing – charging the battery,