®
Shanghai Yatai Instrument Ltd JC Series Electric Counter User Manual
Address: Marketing Department: 8F Rongxin Mansion, 1851 North Sichuan Road Shanghai China, Tel: 021-51053127; 51053128
Technical support and Factory: No. 128 Zhenyuan Rd, Baoshan City industrial Park, Shanghai China, Tel: 021-36160962, 36160096 (English)
⑸
output control
Press
＂▲＂，
modify
single digit as
following :
→
→ →
Please refer to Table 3 for details of
、 、 、
.
⑹
output
control with
mono-stable
time
Press the "
" key to
select the digits need to
be modified until it
flashes, then press the "
▲
"key to modify the
value
Unit is second, the range of delay can select from 0-99.9s.
Note: this function is only available if the control output is
or
. For
or
, this function is not available.
Step 3
⑺
Exiting the
function
parameter
setting mod
e
After the preset value is set and verified according to the Step 1 and Step 2, the press the “preset/parameter”
＜
3s
again, the counter will automatically exit the parameter setting mode and enter the counting mode, and the preset
indicator will be off. If the parameter is not modified, the counter will remain in existing conditions. If the parameter
is modified, the counter will reset to zero and the modified parameters are saved and restart with new parameters.
TALBE 3: Output Action
Output
Increase
Decrease
Action after reaches preset value
RST
SET
OUTPUT
RST
SET
OUTPUT
When RST is set to low level(L), it will be reset, all digital display
reset to 0
，
contact opens
；
RST is set to high level(H), meter starts
counting .When the meter counting value reaches preset value
，
the
contact output is emitted and counting keeps operating until RST is
in reset status
RST
SET
OUTPUT
RST
SET
OUTPUT
When RST is set to low level(L), it will be reset, all digital display
reset to 0
，
contact opens
；
RST is set to high level(H), meter starts
counting .When the meter counting value reaches preset value
，
the
contact output is emitted and counting stops until RST is in reset
status
RST
SET
OUTPUT
RST
SET
OUTPUT
When RST is set to low level(L), it will be reset, all digital display
reset to 0
，
contact opens
；
RST is set to high level(H), meter starts
counting .When the meter counting value reaches preset value
，
the
contact output is emitted and the contact output releases when the
mono-stable delay is ended.
RST
SET
OUTPUT
RST
SET
OUTPUT
When RST is set to low level(L), it will be reset, all digital display
reset to 0
，
contact opens
；
RST is set to high level(H), meter starts
counting .When the meter counting value reaches preset value
，
the
contact output is emitted, counting stops and the contact output
releases when the mono-stable delay is ended.
NOTE:
mono-stable time delay output
(0
~
99.9seconds set)
MAINTAIN ITS OWN STATUS WITH OUTPUT
Additional Information
1. Please wiring according to terminals wiring diagram on the meter
case strictly and ensure the actual power supply is consistent with
the rating value.
2. The connection of sensor and counter must be robust. The signal
lines shall not be placed parallel with the power lines of electric
supply and control lines.
3 please select the sensor reasonably according to requirement and
wiring correctly.
(1) For NPN kind sensor (negative pulse input) or contact counting
signal, the wiring method is shown as Figure 1.
(2) For PNP kind sensor (positive pulse input), the wiring method
is shown as following
(0V)
Contact
Input
+12V
CP1
COM
Control
Circu it
NPN SENSOR
+12V
CP2
COM
Contact
Input
Control
Circu it
PNP SENSOR
4. COM terminal is not only public GND
，
but also output power
supply 0V terminal.
5. For contact sensors, please select low speed (0 – 25Hz) frequency
6. After power is connected, by selecting the required counting
frequency, the counter will enter the normal counting mode.
