YASKAWA Z1000U Series, Руководство по программированию

Страница: 78 / 323

1.7 H: Terminal Functions
H parameters assign functions to the external terminals.
u
H1: Multi-Function Digital Inputs
n H1-01 to H1-08: Functions for Terminals S1 to S8
These parameters assign functions to the multi-function digital inputs. The various functions and settings are listed in Table
1.31 .
No. Parameter Name
Setting
Range
Default
H1-01 Multi-Function Digital Input Terminal S1 Function Selection 1 to B2
40 (F)
<1>
: Forward Run Command (2-Wire sequence)
H1-02 Multi-Function Digital Input Terminal S2 Function Selection 1 to B2
41 (F)
<1>
: Reverse Run Command (2-Wire sequence)
H1-03 Multi-Function Digital Input Terminal S3 Function Selection 0 to B2 24: External Fault (N.O., always detected, coast to stop)
H1-04 Multi-Function Digital Input Terminal S4 Function Selection 0 to B2 14: Fault Reset
H1-05 Multi-Function Digital Input Terminal S5 Function Selection 0 to B2
3 (0)
<1>
: Multi-Step Speed Reference 1
H1-06 Multi-Function Digital Input Terminal S6 Function Selection 0 to B2
4 (3)
<1>
: Multi-Step Speed Reference 2
H1-07 Multi-Function Digital Input Terminal S7 Function Selection 0 to B2
6 (4)
<1>
: Jog Reference Selection
H1-08 Multi-Function Digital Input Terminal S8 Function Selection 0 to B2 8: External Baseblock Command
<1> Number appearing in parenthesis is the default value after performing a 3-Wire initialization (A1-03 = 3330).
Table 1.31 Multi-Function Digital Input Terminal Settings
Setting Function Page
0 3-Wire Sequence 79
3 Multi-Step Speed Reference 1
79
4 Multi-Step Speed Reference 2
6 Jog reference Selection 79
7 Accel/Decel Time Selection 1 79
8 Baseblock Command (N.O.)
80
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold 80
B Drive Overheat Alarm (oH2) 80
C Analog Terminal Input Selection 80
F Through Mode 80
10 Up Command
80
11 Down Command
12 Forward Jog
81
13 Reverse Jog
14 Fault Reset 82
15 Fast Stop (N.O.) 82
17 Fast Stop (N.C.) 82
18 Timer Function Input 82
19 PID Disable 82
1B Program Lockout 82
1E Reference Sample Hold 83
20 to 2F External Fault 83
30 PID Integral Reset 84
31 PID Integral Hold 84
34 PID Soft Starter Cancel 84
35 PID Input Level Selection 84
40 Forward Run Command (2-Wire sequence)
84
41 Reverse Run Command (2-Wire sequence)
Setting Function Page
42 Run Command (2-Wire sequence 2)
84
43 FWD/REV Command (2-Wire sequence 2)
44 Offset Frequency 1
85 45 Offset Frequency 2
46 Offset Frequency 3
47 Node Setup 85
50 Motor Pre-Heat 2 85
51 Sequence Timer Disable 85
52 Sequence Timer Cancel 85
60 Motor Pre-Heat 1 85
61 External Speed Search Command 1 85
62 External Speed Search Command 2 85
63 Field Weakening 85
67 Communications Test Mode 85
69 Jog 2 85
6A Drive Enabled 86
6D AUTO Mode Select 86
6E HAND Mode Select 86
70 Drive Enable2 86
A4 BP Emergency Override 86
A5 BP Drive/Bypass Selection 86
A6 BP BAS Interlock 86
A7 BP Customer Safeties 86
A8 PI2 Disable (N.O.) 86
A9 PI2 Disable (N.C.) 87
AA PI2 Inverse Operation 87
AB PI2 Integral Reset 87
AC PI2 Integral Hold 87
AD Select PI2 Parameters 87
1.7 H: Terminal Functions
78 YASKAWA ELECTRIC SIEP C710636 10C Z1000U HVAC MATRIX Drive Programming Manual