manualshive.com logo in svg

YASKAWA SI-EP3/V, Техническое руководство

Поделиться
Скачать
YASKAWA SI-EP3/V Скачать руководство пользователя страница 12

4  Option Components

YASKAWA

 SIEP YEACOM 06 V1000 Option PROFINET SI-EP3/V  Technical Manual

 12

Table 3  Option LED States

„

Power-Up Diagnostics

An LED test is performed each time the drive is powered up. The initial boot sequence may take several seconds. After 
the LEDs have completed the diagnostic LED sequence, the option is successfully initialized. The LEDs then assume 
operational conditions as shown in 

Table 3

.

Table 4  Power-Up Diagnostic LED Sequence

Name

Indication

Operating Status

Remarks

Color 

Status

MS
(visible through
drive cover)

–

OFF

Power supply OFF

Power is not being supplied to the drive.

Green ON

Option 

operating 

The option is operating normally and 
initialization is complete.

Green

Flashing (1)

Diagnostics

Diagnostic data available.

Green

Flashing (2)

Configuration tool

Identified by a configuration tool.

Red 

ON

Default MAC or fatal error occurred.

Default MAC address has been programmed or 
the option has detected an unrecoverable error.

Red 

Flashing (1)

Configuration error (non-fatal)

Configuration error.

Red 

Flashing (2)

No IP (non-fatal)

No IP address assigned.

Red 

Flashing (3)

No station name (non-fatal)

No station name assigned.

Red 

Flashing (4)

Init failure (non-fatal)

Failed to initialize module.

Green/Red

Flashing

Option self-test

The option is in self-test mode.

NS
(visible through
drive cover)

–

OFF

Offline or Power supply OFF

–

Green ON

Connected

Connection established with I/O controller and 
in RUN mode.

Green

Flashing 

Connected and stopped

Connection established with I/O controller and 
in STOP mode.

Red 

ON

BUS fault

Unrecoverable BUS fault.

Red Flashing 

(1)

Lost 

communication

Host communication is temporarily lost.

Red Flashing 

(2)

Lost 

link

No 

link detected to network.

10/100
(visible at 
RJ45 jack)

Yellow

OFF

10 Mbps is established

–

Yellow 

ON

100 Mbps is established

–

LINK/ACT
(visible at 
RJ45 jack)

Green 

OFF

Link is not established

–

Green

ON

Link is established

–

Green

Flashing

Link is established and there is network 
activity

–

Sequence

Module Status (MS)

Network Status (NS)

Time (ms)

1

Green

OFF

250

2

Red

OFF

250

3

Green

OFF

-

4

Green

Green

250

5

Green

Red

250

6

Green

OFF

-

Содержание SI-EP3/V






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды