YASKAWA S-V Seres Скачать руководство пользователя страница 18

Страница: 18 / 88

1 Checking Products

1-2

1.1

Checking Products on Delivery

(1) When the Universal Feedback Module is Not Connected to the SERVOPACK

Mount the Universal Feedback Module to the SERVOPACK as described in the enclosed

-V

Series Universal Feedback Module Installation Guide

(YEU TOEP C720829 03).

For the location of the nameplate, refer to

Option case unit type code

Check the nameplate to confirm that the product is the one that was ordered.
For the nameplate, refer to

Nameplate and Model Designation

(2) When the Universal Feedback Module is Connected to the SERVOPACK

Check the nameplate to confirm that the Module that is mounted is the Universal Feedback Module.

The nameplate is located in the following position.

1.2

Nameplate and Model Designation



Nameplate Example

Nameplate

OFB01A

Application Module model number

Name

Manufacturing number

SGDV

OPTION MODULE

MODEL SGDV-OFB03A

0/N 123456-1-1
S/N 123456789ABCDEF

YASKAWA EUROPE GMBH

MADE IN JAPAN

Содержание S-V Seres

























































































Результаты поиска

Содержание S-V Seres

Отзывы:

YASKAWA S-V Seres, Руководство пользователя, Страница: 18 / 88

Результаты поиска

Содержание S-V Seres

Отзывы: