background image

Document Revision:  v1.0.5

of

2

10

page

18805 Adams Ct., #110   ~   Morgan Hill, CA 95037, USA   ~  +1-408.924.0808   ~   www.washlinksystems.com   ~   [email protected]

Document Title:  Tech Guide ~ Yaskawa V1000 Basic User Guide 

WASHLINK SYSTEMS

Yaskawa V1000 Basic User Guide

This document provides basic information for navigating and adjusting your Washlink Systems 
supplied Yaskawa V1000 Variable Frequency Drive.

When emailing or  calling for assistance, you must have the following information available:

Location Name:

______________________________

Contact Person:

______________________________

Contact Phone:

______________________________

VFD Model:

______________________________

Equipment connected: ______________________________

Distributor Name:

______________________________

COPYRIGHT

2013 Washlink Systems.  All rights reserved.

THIS DOCUMENT IS THE EXCLUSIVE PROPERTY OF WASHLINK SYSTEMS AND IS PREPARED 
ONLY FOR USE BY THE COMPANY PURCHASING THE EQUIPMENT.  EDITING, COPYING, 
DISTRIBUTING, AND/OR SELLING THIS DOCUMENT IS STRICTLY PROHIBITED WITHOUT PRIOR 
WRITTEN CONSENT FROM WASHLINK SYSTEMS.  WASHLINK SYSTEMS RESERVES THE RIGHT 
TO EDIT THIS DOCUMENT IN ANY MANNER DEEMED NECESSARY, AT ANY TIME, AND WITHOUT 
PRIOR NOTICE.

Содержание PROFINET V1000











Отзывы: