YASKAWA Motoman MH Series Скачать руководство пользователя страница 41

Страница: 41 / 116

INSTALLATION

MOTO

MAN

4-17

MH–Series Positioner Manual with MotoMount

4.4.5

Installing the Bearing Housing Base

The pillow block base (see Figure 4-20) is mounted on top of the tailstock column.
Install the mounting bolts finger tight. Tighten to prescribed torque, 76 N • m (56
lbf-ft).

Figure 4-20 Install Pillow Block Base

4.4.6

Tooling Fixture Installation (initial)

The initial tooling installation is required prior to the headstock/tailstock
alignment procedure.

1. Jog the headstock to the HOME position. The tooling mounting holes and

locating pin must be pointing up. If not, remove the MotoMount drive
components and reinstall in the proper orientation.

WARNING!

Make certain servo power is OFF for the remainder of the
installation, or serious operator injury and/or equipment damage
may result.

2. Use a suitable lifting device to position the tooling above the headstock/

tailstock assemblies.

3. Slowly lower tooling fixture (see Figure 4-21) while aligning with the

headstock locating pin and guide the tailstock bearing into the pillow block
base.

TAILSTOCK COLUMN

PILLOW BLOCK BASE

NOTE: THE MH450 TAILSTOCK IS SHOWN. THE MH75/150

VERSIONS USE 2 BOLTS.

Содержание Motoman MH Series





















































































































Результаты поиска

Содержание Motoman MH Series

Отзывы:

Похожие инструкции для Motoman MH Series

Бренды по названию

Популярные бренды

YASKAWA Motoman MH Series, Руководство пользователя

Результаты поиска

Содержание Motoman MH Series

Отзывы:

Похожие инструкции для Motoman MH Series

Бренды по названию

Популярные бренды