YASKAWA DI-A3 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 24

YASKAWA DI-A3 Скачать руководство пользователя страница 6

1 Preface

6

YASKAWA ELECTRIC

TOBP C730600 39A YASKAWA AC Drive-Option Card DI-A3 Installation Manual

■

General Safety

General Precautions

• The diagrams in this section may include option units and drives without covers or safety shields to

illustrate details. Be sure to reinstall covers or shields before operating any devices. The option
board should be used according to the instructions described in this manual.

• Any illustrations, photographs, or examples used in this manual are provided as examples only and

may not apply to all products to which this manual is applicable.

• The products and specifications described in this manual or the content and presentation of the

manual may be changed without notice to improve the product and/or the manual.

•

When ordering a new copy of the manual due to damage or loss, contact your Yaskawa

representative or the nearest Yaskawa sales office and provide the manual number shown on the front
cover.

DANGER

Heed the safety messages in this manual.
Failure to comply will result in death or serious injury.
The operating company is responsible for any injuries or equipment damage resulting
from failure to heed the warnings in this manual.

NOTICE

Do not expose the drive to halogen group disinfectants.
Failure to comply may cause damage to the electrical components in the option unit
Do not pack the drive in wooden materials that have been fumigated or sterilized.
Do not sterilize the entire package after the product is packed.

«
...
4
5
6
7
8
...
»

Содержание DI-A3

























Отзывы:

Нет отзывов