manualshive.com logo in svg

YASKAWA D1000 Series, Инструкция по эксплуатации, Страница: 172 / 251

Поделиться
Скачать
YASKAWA D1000 Series Скачать руководство пользователя страница 172

172

 

YASKAWA ELECTRIC

 TOEP C710656 07A YASKAWA Power Regenerative Converter - D1000 Instruction Manual

A.4  Derating Data

A.4 Derating Data

The converter can be operated at above the rated temperature, altitude, and default carrier frequency by derating the 
converter capacity.

◆

Temperature Derating

To ensure the maximum performance life, the converter output current must be derated as shown in 

Figure A.1

 when the 

converter is installed in areas with high ambient temperature or if converters are mounted side-by-side in a cabinet. In 
order to ensure reliable converter overload protection, set parameters L8-35 according to the installation conditions.

■

Parameter Settings

If the ambient temperature is higher than the rating or if converters are installed side by side in the control panel, you must 
set the L8-12 and L8-35 parameters according to the installation conditions. Derate the output current according to 

Figure A.1

Setting 0: IP00/IP20/Open-Chassis Enclosure

Converter operation between -10

°

C and +50

°

C allows 100% continuous current without derating.

Setting 1: Side-by-Side Mounting

Converter operation between -10

°

C and +30

°

C allows 100% continuous current without derating. Operation between 

+30

°

C and +50

°

C requires output current derating.

Setting 3: External Heatsink Installation

Converter operation between -10

°

C and +40

°

C allows 100% continuous current without derating. Operation between 

+40

°

C and +50

°

C requires output current derating.

Figure A.1  

Figure A.1  Ambient Temperature and Installation Method Derating

◆

Altitude Derating

Standard ratings are valid for installation altitudes up to 1000 m. For installations from 1000 m to 3000 m, the converter 
rated voltage and the rated output current must be derated for 1% per 100 m.

No.

Name

Description

Setting Value

Default Setting

L8-12

Ambient Temperature 
Setting

Adjust the converter overload (oL2) protection level 
when the converter is installed in an environment that 
exceeds its ambient temperature rating.

-10 to +50

+40

°

C

L8-35

Installation Method 
Selection

0: IP00/IP20/Open-Chassis Enclosure
1: Side-by-Side Mounting
3: Finless converter or External Heatsink Installation

0, 1, 3

Default setting is 

determined by o2-04 

(drive model 

selection).

100

85

70

55

0

L8-35=3: External Heatsink Installation

L8-35=0

：

IP00, IP20

30

-10

40

50

L8-12
(Ambient temp: °C)

L8-35=1: Side-by-Side Mounting

Содержание D1000 Series




























































































































































































































































Отзывы:

Нет отзывов