348
YASKAWA
SIEPC71061723A YASKAWA AC Drive CR700 Technical Manual
Code
Name
Causes
Possible Solutions
The V/f pattern settings are incorrect.
•
Examine the ratios between the V/f pattern frequency and
voltage. Decrease the voltage if it is too high compared to the
frequency.
•
Adjust
E1-xx [V/f Pattern Parameters]
settings. For motor 2,
adjust
E3-xx [V/f Pattern for Motor 2]
settings. For motor 3,
adjust
E7-xx [V/f Pattern for Motor]
settings.
Torque compensation gain is too large.
Decrease the value set in
C4-01 [Torque Compensation Gain]
so
that the motor does not stall.
A malfunction occurred due to noise.
Check the control circuit lines, main circuit lines, and ground
wiring, and minimize the effects of electrical interference.
The gain during overexcitation operation is set too
large.
•
Identify the timing under which the fault occurs.
•
If the fault occurs simultaneously with overexcitation
operation, reduce the value set in
n3-13 [Overexcitation
Deceleration Gain]
, considering the motor flux saturation.
The drive received a Run command while the motor
was coasting.
Reevaluate the sequence to ensure that the stop command is input
after the motor has come to a complete stop.
The control method is not set correctly for the
motor being used.
Set
A1-02 [Control Method Selection]
correctly.
The motor main circuit cable is too long.
Replace the drive with a larger capacity model.
Note:
•
Occurs if the drive sensors detect a drive output current exceeding the specified overcurrent detection level.
•
Do a Fault Reset to clear the fault.
Code
Name
Causes
Possible Solutions
oFA00
Option Not Compatible with Port
The option connected to connector CN5-A is not
compatible.
Connect the option to the correct connector.
Note:
Encoder options are not compatible with connector CN5-A.
Note:
•
Do a Fault Reset to clear the fault.
•
Fault trace is not available for these faults.
Code
Name
Causes
Possible Solutions
oFA01
Option Fault/Connection Error
The option card connected to connector CN5-A is
not compatible.
1. De-energize the drive.
2. Refer to the option card manual and correctly connect the
option card to the connector on the drive.
Note:
Do a Fault Reset to clear the fault.
Code
Name
Causes
Possible Solutions
oFA02
Duplicate Options
The same option cards or the same type of option
cards are connected to connectors CN5-A, B, and C.
Connect the option card to the correct connector.
Note:
Use connectors CN5-C and CN5-B to connect two encoder
option cards.
Note:
Do a Fault Reset to clear the fault.
Code
Name
Causes
Possible Solutions
oFA03
Diagnostic Error
A fault occurred in the option card.
1. De-energize the drive.
2. Make sure that the option card is correctly connected to the
connector.
3. If the problem continues, replace the option card.
Note:
Do a Fault Reset to clear the fault.
Code
Name
Causes
Possible Solutions
oFA04
Flash Write Mode
A fault occurred in the option card.
1. De-energize the drive.
2. Make sure that the option card is correctly connected to the
connector.
3. If the problem continues, replace the option card.
Note:
Do a Fault Reset to clear the fault.
Code
Name
Causes
Possible Solutions
oFA05
Option A/D Error
A fault occurred in the option card.
1. De-energize the drive.
2. Make sure that the option card is correctly connected to the
connector.
3. If the problem continues, replace the option card.
Note:
Do a Fault Reset to clear the fault.
Содержание CR700
