YASKAWA 2A0001, Техническое руководство

Страница: 379 / 512

No. Name Description Range Def.
Control
Mode
Addr.
Hex
Pg.
V/
f
O
L
V
P
M
H2-06 Watt Hour Output Unit Selection
Sets the output units for the watt hours when
Watt Hour Pulse Output is selected as the digital
output (H2-01, H2-02, or H2-03 = 39).
Outputs a 200 ms pulse signal when the watt-
hour counter increases by the units selected.
0: 0.1 kWh units
1: 1 kWh units
2: 10 kWh units
3: 100 kWh units
4: 1000 kWh units
0 to 4 0 A A A 437 204
<1> The availability of certain functions depends on the control method used.
H2 Multi-Function Digital Output Settings
H2- oo
Setting
Function Description
Control
Mode
Pg.
V/
f
O
L
V
P
M
0 During Run Closed: A Run command is active or voltage is output. O O O 195
1 Zero Speed Closed: Output frequency is 0. O O O 196
2 Speed Agree 1
Closed: Output frequency equals the speed reference (plus or minus the hysteresis set
to L4-02).
O O O 196
3 User Set Speed Agree 1
Closed: Output frequency and speed reference equal the value in L4-01 (plus or minus
the hysteresis of L4-02).
O O O 196
4 Frequency Detection 1
Closed: Output frequency is less than or equal to the value in L4-01 with hysteresis
determined by L4-02.
O O O 197
5 Frequency Detection 2
Closed: Output frequency is greater than or equal to the value in L4-01, with hysteresis
determined by L4-02.
O O O 197
6 Drive Ready
Closed: Drive Ready. The drive is powered up, not in a fault state, and in the Drive
mode.
O O O 198
7 DC Bus Undervoltage Closed: DC bus voltage is below the Uv trip level set in L2-05. O O O 198
8 During Baseblock (N.O.) Closed: There is no output voltage O O O 198
9 Frequency reference selection Open: External Reference 1 or 2 supplies the frequency reference
Closed: Digital operator supplies the frequency reference.
O O O 198
A Run command selection
Open: External Reference 1 or 2 supplies the Run command
Closed: Digital operator supplies the Run command.
O O O 198
B Torque Detection 1 (N.O.)
Closed: Output current/torque exceeds the torque value set in parameter L6-02 for longer
than the time set in parameter L6-03.
O O O 198
C Frequency Reference Loss Closed: Loss of the analog frequency reference detected. Enabled when L4-05 = 1. O O O 199
D Braking Resistor Fault
Closed: Braking resistor or transistor is overheated or faulted out. This selection requires
that braking resistor protection parameter be set for ERF (L8-01 = “1”).
O O O 199
E Fault Closed: Fault occurred (other than CPF00 and CPF01). O O O 199
F Not used/Through Mode
Set this value when the terminal is not used, or when using the terminal in the pass-
through mode.
O O O 199
10 Minor Fault Closed: An alarm is triggered. O O O 199
11 Reset Command Active
Closed: The drive has received a reset command from the multi-function input terminals
or from serial network, or the digital operator RESET key has been pressed.
O O O 199
12 Timer Output
Timer output, controlled by b4-01 and b4-02. Used in conjunction with the digital input
(H1- oo = 18 “timer function”).
O O O 199
13 Speed Agree 2 Closed: When drive output frequency equals the frequency ref/- L4-04. O O O 199
14 User Set Speed Agree 2
Closed: When the drive output frequency is equal to the value in L4-03 (plus or minus
L4-04).
O O O 200
15 Frequency Detection 3
Closed: When the drive output frequency is less than or equal to the value in L4-03 with
the hysteresis determined by L4-04.
O O O 200
16 Frequency Detection 4
Closed: When the output frequency is greater than or equal to the value in L4-03 with
the hysteresis determined by L4-04.
O O O 201
B.2 Parameter Table
YASKAWA ELECTRIC SIEP C710606 18F YASKAWA AC Drive – V1000 Technical Manual 379
B
Parameter List