background image

model no. 060-1984-8  |  contact us: 1.866.523.5218

14” (36 CM) BRUSHLESS GRASS TRIMMER 

1

Quick Start Guide

1.   ASSEMBLING THE UPPER SHAFT AND LOWER SHAFT  

Connect the couplings together. (See Fig. A1)
Align the holes and fasten the couplings by tightening the bolt with hex key. (See Fig. A2)

2.  ASSEMBLING THE AUXILIARY 

HANDLE

Place the auxiliary handle onto the shaft 
from the top, and align with the anti-vibration 
circle on the shaft. Secure the auxiliary 
handle by tightening the four bolts with the 
hex key. (See Fig. B) 

3.  ASSEMBLING THE SAFETY GUARD

Attach the safety guard to the trimmer head. Align the guard so it slides into the slots 
located on the trimmer head. (See Fig. C1)
Secure the safety guard onto the trimmer head with the bolts provided by using hex key. 
(See Fig. C2)    
Please put the hex key back to the top notch of grass trimmer after use, so it will not get 
lost. (See Fig. C3) 

A1

B

C2

C1

A2

* This information is provided for your convenience. It does not replace the instruction manual 
and safety instructions. The manual and safety instructions need to be read and understood in 
their entirety.

Содержание CGT48BCU



























Отзывы: