YARDMAX YP7065 Скачать руководство пользователя страница 21

Страница: 21 / 28

TROUbLESHOOTInG

Problem

Cause

Remedy

Engine fails to start

1. Spark plug wire disconnected

2. Out of fuel or stale fuel

3. Choke not in open position

4. blocked fuel line

5. Fouled spark plug

6. Engine flooding

1. Attach spark plug wire securely to spark plug

2. Fill with clean, fresh gasoline

3. Throttle must be positioned at choke for a

cold start

4. Clean the fuel line

5. Clean, adjust gap, or replace

6. Wait a few minutes to restart, but do not prime

Engine runs
erratically

1. Spark plug wire loose

2. Unit running on CHOKE

3. blocked fuel line or stale fuel

4. Vent plugged

5. Water or dirt in fuel system

6. Dirty air cleaner

7. Improper carburetor adjustment

1. Connect and tighten spark plug wire

2. Move choke lever to OFF

3. Clean fuel line. Fill tank with clean, fresh

gasoline

4. Clear vent

5. Drain fuel tank. Refill with fresh fuel

6. Clean or replace air cleaner

7. Refer to Engine Manual

Engine overheats

1. Engine oil level low

2. Dirty air cleaner

3. Air flow restricted

4. Carburetor not adjusted

properly

1. Fill crankcase with proper oil

2. Clean air cleaner

3. Remove housing and clean

4. Refer to Engine Manual

Power sweeper
does not sweep
while engine is
running

1. The brush is blocked by the dirt

and debris

2. belt slack or worn

3. The left upper lever loosen or

worn

1. Stop engine, and then remove the dirt and

debris

2. Have belt tightened. Have worn belt

replaced

3. Have loosen lever tightened. Have worn

lever replaced

Power sweeper
does not drive along

1. Coupling cable for drive

system not adjusted correctly

2. belt slack or worn

3. Tire worn

1. Adjust coupling cable

2. Have belt tightened. Have worn belt

replaced

3. Have worn tire replaced

Excessive vibration

Loose parts or damaged worm

Stop engine, and then tighten loose bolts and
nuts and have damaged worm repaired

Power Sweeper

Operator’s Manual

Troubleshooting

32530US25M100.indd 20

2016/9/23 14:48:53

Содержание YP7065





























Результаты поиска

Содержание YP7065

Отзывы:

Бренды по названию

Популярные бренды

YARDMAX YP7065, Руководство оператора

Результаты поиска

Содержание YP7065

Отзывы:

Бренды по названию

Популярные бренды