manualshive.com logo in svg

Yardistry YM12944, Инструкция по установке и эксплуатации

Поделиться
Скачать
Yardistry YM12944 Скачать руководство пользователя страница 23

 23 

[email protected]

Hardware

Fig. 5.6

Long Beam 

Assembly

Short Side 

Assembly

Step 5: Frame Assembly and Anchoring 

Part 3

x 4

8 x  3/8 x 9-1/2” Hex Bolt (3/8” large washer x 2, 3/8” lock nut)

F:  

Move your Short Side Assemblies to the final location.  Make sure the ground is flat and level before continuing 

assembly.

G:

  With helpers stand up Short Side Assemblies then place one Long Beam Assembly against the outside of two 

Post Assemblies, flush to the tops and outside corners and tight to Short Beam Assembly.  Attach Long Beam 

Assembly to Post Assembly through the top and bottom holes with two 3/8 x 9-1/2” Hex Bolts (with two 3/8” large 

washers and one 3/8” lock nut) per Post Assemby.  Repeat for the second Long Beam Assembly on the opposite 

side.  (fig. 5.6 and 5.7)  

Long Beam 

Assembly

Short Side 

Assembly

Post 

Assembly

Post 

Assembly

Post 

Assembly

3/8” Large 

Washer

3/8 x 9-1/2” 

Hex Bolt

3/8” 

Lock Nut

Short Beam 

Assembly

Long Beam 

Assembly

Flush 

and tight

Fig. 5.7

Post 

Assembly

Use 

these 

holes

Содержание YM12944



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды