manualshive.com logo in svg

Yard-Man Style L, Руководство оператора

Поделиться
Скачать
Yard-Man Style L Скачать руководство пользователя страница 20

20

SECTION 8:  TROUBLE SHOOTING GUIDE

NOTE: 

For repairs beyond the minor adjustments above, contact your local authorized service dealer.

Trouble

Possible Cause(s)

Corrective Action

Engine fails to start

Fuel tank empty, or stale fuel.

Blocked fuel line.
Choke control not in ON position
Faulty spark plug.
Ignition key not present.
Spark plug wire disconnected.
Engine not primed.

Fill tank with clean, fresh gasoline. Fuel will not last over thirty days 
unless a fuel stabilizer is used.
Clean fuel line.
Move choke control to ON position
Clean, adjust gap or replace.
Insert key into ignition switch.
Connect spark plug wire.
Refer to the 

Tecumseh 

engine manual or 

Starting the Engine

 on page 

10 of this manual for instructions on the engine primer.

Engine runs erratic

Unit running on CHOKE.
Blocked fuel line or stale fuel.

Water or dirt in fuel system.
Carburetor out of adjustment.

Move choke control to OFF position.
Clean fuel line; fill tank with clean fresh gasoline. Fuel will not last 
over thirty days unless a fuel stabilizer is used.
Drain fuel tank. Refill with fresh fuel.
Refer to the 

Tecumseh

 engine manual.

Loss of power

Spark plug wire loose.
Gas cap vent hole plugged.
Exhaust port plugged.

Connect and tighten spark plug wire.
Remove ice and snow from cap. Be certain vent hole is clear.
Clean following the engine manual.

Engine overheats

Carburetor not adjusted 
properly.

Refer to the 

Tecumseh 

engine manual packed with your unit or 

have carburetor adjusted by an authorized service dealer.

Excessive vibration

Loose parts or damaged auger.

Stop engine immediately and disconnect spark plug wire. Tighten 
all bolts and nuts. Make all necessary repairs. If vibration 
continues, have unit serviced by an authorized service dealer.

Unit fails to propel itself Incorrect adjustment of drive 

control cable.
Drive belt loose or damaged.

Adjust drive control cable.

Replace drive belt.

Unit fails to
discharge snow

Chute assembly clogged.

Foreign object lodged in auger.
Incorrect adjustment of auger 
control cable.
Drive belt loose or damaged.

Stop engine immediately. Clean chute assembly and inside of 
auger housing with chute clean-out tool
Stop engine immediately. Remove object from auger.
Adjust auger control cable.

Replace drive belt.

Содержание Style L





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды