Yard-Man 31AE553F401 Скачать руководство пользователя страница 14

 14

WARNING:  Do not attempt to change the
auger belt without the help of an assistant. It
is very important that one person, standing
at the operating position, firmly hold the
snow thrower housing to prevent it from
tipping while the other person replaces the
belt. Failure to comply with this may result
in injury.

Figure 18  

4.

Standing in the operating position, lift up on the 
handles and pull the frame assembly rearward. 
The frame and the housing will separate, and 
the rear auger belt will come off the pulley. 
Maintain control of the frame assembly while 
pulling it.

5.

Remove the two belts from the two engine pulleys. 
For location of the pulleys, see Figure 19.    

Figure 19  

6.

To remove the front auger drive belt, push the 
idler pulley to the left. The belt brake should 
move outward. See Figure 20. Lift the front 

auger drive belt from the front auger pulley.  

Figure 20  

7.

Place new belts on the two auger pulleys making 
sure that the front auger belt is under the belt 
brake. Route belts under and to the left of the 
flat idler pulley. Hold the belts upward in this 
position.

8.

While lifting up on the handles, bring the frame 
assembly close to the auger housing, and place 
the two belts on the front and rear engine 
pulleys. See  Figure 21.   

Figure 21  

9.

Level the frame assembly and tip the auger 
housing forward to align studs with the 
corresponding holes on both sides of the frame 
assembly. See Figure Figure 18. Push the frame 
assembly fully on to the studs.

NOTE: Use care to avoid pinching the control cable.

10. From the frame assembly side, insert six lock 

washers and hex nuts on to the studs . These 
pieces of hardware were removed earlier. 
Tighten the nuts securely.

11. Reinstall the belt cover on the front of the engine 

with the two self-tapping screws and flat 
washers.

12. Reattach the chute crank to the chute assembly 

with the hairpin clip and flat washer. 

NOTE: Make sure that the auger cable is routed in 
front of the belt. 

Lock

Washer,

Hex Nut

studs

Align

with 
holes on
Frame

Assembly

Front

Engine 

Pulley

Rear

Engine

Pulley

Idler

Pulley

Drive Belt

Auger

Belt

Shift auger

Belt Brake

idler pulley

Frame Assembly 

Auger Housing

Содержание 31AE553F401





























Отзывы: