Yard Machines LT31CSH Скачать руководство пользователя страница 3

3

RULES FOR SAFE OPERATION

READ ALL INSTRUCTIONS 

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill, or under the

influence of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use

the unit, except for teens guided by an adult.

• All guards and safety attachments must be installed

properly before operating the unit.

• Inspect the unit before use. Replace damaged parts.

Check for petrol leaks. Make sure all fasteners are in
place and secure. Replace parts that are cracked,
chipped, or damaged in any way. Do not operate the
unit with loose or damaged parts.

• Carefully inspect the area before starting the unit.

Remove all debris and hard or sharp objects such as
glass, wire, etc.

• Be aware of the risk of injury to the head, hands and

feet.

• Clear the area of children, bystanders, and pets. At a

minimum, keep all children, bystanders, and pets
outside a 15 m (50 foot) radius; there still may be a risk
to bystanders from thrown objects. Bystanders should
be encouraged to wear eye protection. If you are
approached, stop the unit immediately.

• Use only 

2.41mm (0.095 inch) diameter original

equipment manufacturer replacement line. Never use
metal-reinforced line, wire or rope. These can break off
and become dangerous projectiles. 

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments
or repairs before using unit.

SAFETY WARNINGS FOR PETROL UNITS

• Store petrol only in containers specifically designed

and approved for the storage of such materials.

• Avoid creating a source of ignition for spilled petrol.

Do not start the engine until petrol vapors dissipate.

• Always stop the engine and allow it to cool before

filling the feul tank. Never remove the feul tank cap or
add fuel when the engine is hot. Never operate the unit
without the fuel cap securely in place. Loosen the fuel
tank cap slowly to relieve any pressure in the tank.

SYMBOL

MEANING

The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.

NOTE:

Advises you of information or instructions vital to
the operation or maintenance of the equipment.

SYMBOL

MEANING

When using the unit,
you must follow the

safety rules. Please read these instructions
before operating the unit in order to ensure
the safety of the operator and any bystanders.
Please keep these instructions for later use.

WARNING:

• IMPORTANT SAFETY INSTRUCTIONS •

Failure to obey a
safety warning can

result in injury to yourself and others.
Always follow the safety precautions to
reduce the risk of fire, electric shock and
personal injury.

WARNING:

Failure to obey a
safety warning will

result in serious injury to yourself or to
others. Always follow the safety precautions
to reduce the risk of fire, electric shock and
personal injury.

DANGER:

Failure to obey a
safety warning may

result in property damage or personal injury
to yourself or to others. Always follow the
safety precautions to reduce the risk of fire,
electric shock and personal injury.

CAUTION:

Indicates
danger,

warning or caution. Attention is required in
order to avoid serious personal injury. May
be used in conjunction with other symbols
or pictographs.

SAFETY ALERT:

Petrol is highly
flammable, and its

vapors can explode if ignited. Take the
following precautions:

WARNING:

Read the Operator’s Manual(s) and follow all

warnings and safety instructions.

Failure to do so can result in serious injury to the

operator and/or bystanders.

Содержание LT31CSH

























Отзывы: