13
gun while system is pressurized.
• NEVER aim spray gun at people, animals, or plants.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is
running.
• NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING!
Exhaust heat/gases could ignite
combustibles, structures or damage fuel
serious injury.
serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer, or
dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
How To Use Quick-Connect Nozzles
Follow these instructions to change nozzles:
The quick-connect on the spray wand allows you to switch
between the 4 different quick-connect nozzles included with
this pressure washer. Nozzles can be changed while the
pressure washer is running once the spray gun trigger is
locked. The nozzles vary the spray pattern as shown.
1. Pull back collar on spray wand and pull current nozzle out.
Store nozzles in holders on the accessory bracket attached
to the handle.
WARNING
The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER change nozzles without the trigger locked on the
spray gun.
• DO NOT twist nozzles while spraying.
2.Select desired nozzle.
• For general rinsing, ideal for most all purpose cleaning
such as home siding, brick patios, wood decks,
driveways and sidewalks, garage floors, etc., select
yellow 15° nozzle.
• For delicate rinse, for gentle cleaning of cars trucks,
boats, RV's, patio furniture, lawn equipment, etc., select
white 40° nozzle.
• To apply detergent, applies project specific cleaners to
help break down stubborn dirt and grime on a variety of
surfaces, select black detergent nozzle.
• For cleaning of hard surfaces like cement, metal, brick, etc.
use the 0° nozzle. CAUTION! This nozzle generates a very
powerful stream that will damage softer materials including
wood, plastic and textile. NEVER use this nozzle to clean
any part of any vehicle.
3.Pull back on collar, insert new nozzle and release collar.
Tug on nozzle to make sure it is securely in place.
Cleaning Suggestions
• For most effective cleaning, keep nozzle from 8 to 24 inches
(20 to 61 cm) away from cleaning surface.
• If you get nozzle too close, especially using a high pressure
nozzle, you may damage surface being cleaned.
• Do Not get closer than 6 inches (15 cm) when cleaning
tires.
0°
15°
40°
Soap
WARNING!
The high pressure stream of water that this
pressure washer produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which could result in
serious injury.
• DO NOT allow CHILDREN to operate pressure washer.
• Keep high pressure hose connected to pump and spray
2.Bring the remote control close to remote control connection
button, press and hold the stop button on the remote control
until the green light flashes as the frequency of once per
second. Then the remote function is ready.
When pressing the buttons on the remote control, if the red
LED is not illuminated, please replace the remote control
battery. To replace the battery, please open the back of the
remote control, change two old cells with two new batteries.
(Battery type: CR2016).
To buy a new remote control, please call the Yard Force
helpline at 1-866-902-9690
NOTICE:
• Replacement parts must be the same and installed in
the same position as the original parts.
