2.
Hold down the battery buckle and remove the battery from the radio's body.
3.
Move left to overturn the top of the USIM card holder, install the USIM card into the card
holder, and pay attention to the direction of the notch.
4.
Put the battery in and install it.
NOTE:
Before taking out the battery, we must swirl the switch knob to turn off the ma
-
chine and do not remove the battery directly in the open state. This may lead to the loss
of the data of the mobile phone and even the unrepairable damage.
Basic Use
1. POWER-ON:
In power off mode, turn on the power switch / volume knob clockwise .
When radio logging in . Voice prompt “dudu…Log in…..Search the network (green light
flash). After successful logged in network (green light slow), there will be a voice prompt
for the current group and members.
2. POWER OFF:
when power on ,turn off the power switch / volume knob in the counter
-
clockwise direction until switch off.
3. ADJUSTING VOLUME:
turn on the volume potentiometer to achieve the reasonable
volume.
4. SELECT GROUP (group calling), SINGLE CALL SELECTION (single call), SELECT
FRIENDS (group calls):
Short press the side key 1 or MENU function key, enter the
menu, and operate the corresponding button according to the screen prompt. In this
mode, if it does not operate for more than 15 seconds, it will automatically exit the selec-
tion mode, or press EXIT to exit or return to the default group mode standby.
5. SYSTEM SETUP OPERATION (menu list):
Short press the side key 1 or MENU func-
tion key, enter the system menu, and operate the corresponding button according to
the screen prompt. In this mode, if it does not operate for more than 15 seconds, it will
automatically exit the selection mode, or press EXIT to exit or return to the default group
mode standby.
6. GPS SWITCH:
Platform settings, be activated when power on.(GPS optional)
7. CURRENT USER QUERY:
in standby mode, short press side key 3 will voice prompt
current group and user name.
8. POWER, SIGNAL AND NETWORK ENQUIRIES:
standby mode, short press side key 4,
voice prompt the current battery power, wireless signal level and current network mode.
Troubleshooting Guide
If your walkie talkie is in the process of using the following phenomenon, please check the
following information first, if you can not fix the problem, please contact the dealer.
Problem
Investigation Method
Solution
Poor signal
reception
The current location network signal
is weak at present
1.
Please move to the location where
you can receive the network well.
2.
Please avoid using it at a similar
time interval or try again later.
Call intermittently
or delay
Base station switching or poor
radio signal or bad network relay
lines of network operators.
After the shutdown, restart the sys-
tem, you can automatically search the
base station and switch to the better
quality network.
e.
Side key 4:
A. Entering the function menu, such as group selection, single call selection, friend
search, system settings and so on, short press as down key.
B. in standby mode, prompt the current power, signal intensity, network mode by short
press.
f.
MENU:
In standby mode, short press enter function menu.
g.
UP:
Entering the function menu, such as: group selection, single call selection, friend
search, system settings and so on, short press as up button.
h.
OK:
Enter the function menu settings, short press as the confirmation key.
i.
EXIT:
Entering the function menu, such as group selection, single call selection, friendly
search, system settings and so on, short press as down key or return to the previous
menu.
j.
DOWN:
Entering the function menu, such as group selection, single call selection, friend
search, system settings and so on, short press as down key.
k.
The earphone interface:
Insert the headset and press the PTT button on the headset
to communicate. Release to cancel the communicate .
l.
USB:
Module software upgrade interface.
This radio account setting or software upgrade
Headphone socket can also be used as a programming interface, cooperate with man-
ufacturers of programming cable, the programming software (compatible with kenwood
program cable) can set the unit of information (account name, password, etc.) To enter
a state of programming, hold the PTT button and then turn on the radio, normally on a
red light into the data programming model.
When the battery power is too low:
There will be 4 times beep to remind users to charge and red flashes.
When the battery is overpressure
There will be no voice reminding users, the indicator lights will flash at the same time,
and shut down or can not power on.
Indicator instruction
Radio state
Indicator state
time
Searching for a network state
Green light, flash
0.2S bright, 0.2S extinguish
Standby state
Green light, slow flash
1S bright, 1S extinguish
Waiting state (when there is a
GPS signal)
Yellow light, slow flash
0.3S bright, 0.7S extinguish
Transmit state
Red light bright
Receive state
Green light bright
Getting Started
SMART-PTT platform:
register the user account and password in the platform manage-
ment page, set up the user's various functional rights, and insert the valid USIM card (traffic
card) in the registered device.
Install USIM Card
Please prepare a valid USIM card (user identification card) before using this device.
1.
Turn the volume knob / power knob. Turn off the radio.
Содержание T-X8plus
Страница 4: ......
