Yanmar YDG Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 92

Yanmar YDG Series Скачать руководство пользователя страница 42

BEFORE YOU OPERATE

28

YDG Operation Manual

Filling the Fuel Tank

DANGER

Only fill the fuel tank with diesel fuel. Filling the
fuel tank with gasoline may result in a fire and
will damage the engine, never refuel with the
engine running.

Figure 5

1. Clean the area around the fuel cap.

2. Remove the fuel cap (1,

) from the fuel

tank.

CAUTION

Never remove inlet fuel screen from the filler
port when filling the fuel tank. If removed, dirt
and debris could get into the fuel system
causing it to clog.

3. Stop fueling when the fuel is at the same level

as the red ring (2,

) at the bottom of the

inlet fuel screen.

DANGER

Never overfill the fuel tank.

4. Replace the fuel cap and hand-tighten.

Over-tightening the fuel cap will damage it.

ENGINE OIL

The YANMAR YDG generators are equipped with a
low oil pressure stop device. This device stops the
engine automatically when the oil pressure falls
below the specified level and prevents engine
seizure when engine oil is low.

Engine Oil Specifications

NOTICE

Never mix different types of engine oil. This may
adversely affect the lubricating properties of the
engine oil. Only use the engine oil specified. Other
engine oils may affect warranty coverage, cause
internal engine components to seize, and/or
shorten engine life.

Use an engine oil that meets or exceeds the
following guidelines and classifications:



Service categories

• API service categories CD or higher

• ACEA service categories E-3, E-4, and E-5

• JASO service category DH-1



Definitions

• API classification (American Petroleum Institute)

• ACEA classification (Association des

Constructeurs Européens d’Automobilies)

• JASO (Japanese Automobile Standards

Organization)

Note:

• Be sure the engine oil, engine oil storage

containers, and engine oil filling equipment are
free of sediments and water.

• Change the engine oil after the first 50 hours of

operation and then every 200 hours thereafter.

• Select the oil viscosity based on the ambient

temperature where the engine is being operated.
See the SAE service grade viscosity chart
(

).

•

YANMAR does not recommend the use of engine
oil “additives”.

K0002458A-00X

1

2

«
...
40
41
42
43
44
...
»

Содержание YDG Series





























































































Отзывы:

Нет отзывов